bass does not work on 42-380

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

bass does not work on 42-380

gennet2
Junior Member

Posts: 26
Threads: 8
Joined: Jun 2011

06-21-2011, 05:56 AM

Thanks for info Chuck. I didn't replace the bakelite caps only the paper ones. I have never tried to realign it. Is that in the schmatic pages under DIAL CALIBRATION NOTE B adjusting low frequency. NOTE C is adjust high frequency. Other than that I would be lost. The only other thing I have done is to tweek the three cans on top for maximum volume. but I did mark location of each before I turned them. It only took maybe an eigth of a turn to acheive this. Any suggestions or maybe I don't have enough knowledge to do this. I have a multimeter if that is what i need.
Bob

Find

« Next Oldest | Next Newest »

Messages In This Thread

bass does not work on 42-380 - by gennet2 - 06-18-2011, 11:35 AM

Re: bass does not work on 42-380 - by gennet2 - 06-18-2011, 12:54 PM

Re: bass does not work on 42-380 - by exray - 06-18-2011, 04:42 PM

Re: bass does not work on 42-380 - by gennet2 - 06-19-2011, 05:36 AM

Re: bass does not work on 42-380 - by Chuck Schwark - 06-20-2011, 05:00 PM

Re: bass does not work on 42-380 - by gennet2 - 06-21-2011, 05:56 AM

Re: bass does not work on 42-380 - by gennet2 - 06-21-2011, 06:18 AM

Re: bass does not work on 42-380 - by Raleigh - 06-24-2011, 12:31 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean. Can you explain what you are really saying. If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head. Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640. Does that help?--Johngeorgetownjohn — 02:14 PM

Who's Online

There are currently 1944 online users. [Complete List]
» 1 Member(s) | 1943 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me