Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

pilot lamp burn out
#9

NTC thermistor is always a good thing, especially if chosen correctly.
I had to use it a few times, especially when I had to design an off-line SMPS power supply.
The challenge is, the consumption has to be significant for a particular thermistor to cause it to heat up and drop the resistance, at the same time having sufficiently high resistance in the cold state to limit the inrush. This all goes to efficiency, as obviously there are extra losses associated with it.

Of course, with the radios we do not care much about efficiency Icon_smile

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
pilot lamp burn out - by lasurveyor - 06-11-2023, 11:11 AM
RE: pilot lamp burn out - by Paul Philco322 - 06-11-2023, 01:10 PM
RE: pilot lamp burn out - by morzh - 06-11-2023, 01:32 PM
RE: pilot lamp burn out - by Ron Ramirez - 06-11-2023, 01:56 PM
RE: pilot lamp burn out - by lasurveyor - 06-11-2023, 04:39 PM
RE: pilot lamp burn out - by radiorich - 06-11-2023, 08:31 PM
RE: pilot lamp burn out - by morzh - 06-11-2023, 08:43 PM
RE: pilot lamp burn out - by radiorich - 06-12-2023, 07:32 AM
RE: pilot lamp burn out - by morzh - 06-12-2023, 07:37 AM
RE: pilot lamp burn out - by Paul Philco322 - 06-12-2023, 09:30 AM
RE: pilot lamp burn out - by morzh - 06-12-2023, 10:11 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently 3958 online users. [Complete List]
» 1 Member(s) | 3957 Guest(s)
Avatar

>