1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
pilot lamp burn out
morzh
Odobenus rosmarus
*****
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#11

06-12-2023, 11:11 AM
Here.

Take a solid state relay.
Make the switch input powered through an RC. Or a 555 timer. With 20 seconds delay.

And from here you could be as fancy as you like. I do not exclude a possibility of using some microcontroller and even AI. In the latter case make sure it has a display, where for 20 seconds there will be a middle finger displayed and some pleasant voice will tell you were to go and what to do.

Then after 20 seconds it will say "OK, ok...now".
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »


Messages In This Thread
pilot lamp burn out - by lasurveyor - 06-11-2023, 12:11 PM
RE: pilot lamp burn out - by Paul Philco322 - 06-11-2023, 02:10 PM
RE: pilot lamp burn out - by morzh - 06-11-2023, 02:32 PM
RE: pilot lamp burn out - by Ron Ramirez - 06-11-2023, 02:56 PM
RE: pilot lamp burn out - by lasurveyor - 06-11-2023, 05:39 PM
RE: pilot lamp burn out - by radiorich - 06-11-2023, 09:31 PM
RE: pilot lamp burn out - by morzh - 06-11-2023, 09:43 PM
RE: pilot lamp burn out - by radiorich - 06-12-2023, 08:32 AM
RE: pilot lamp burn out - by morzh - 06-12-2023, 08:37 AM
RE: pilot lamp burn out - by Paul Philco322 - 06-12-2023, 10:30 AM
RE: pilot lamp burn out - by morzh - 06-12-2023, 11:11 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 4672 online users. [Complete List]
» 3 Member(s) | 4669 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration