Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Transitone type 3
#15

A great read. Thanks everyone


Messages In This Thread
Transitone type 3 - by R Radbill - 05-05-2023, 09:29 PM
RE: Transitone type 3 - by fenbach - 05-17-2023, 06:29 PM
RE: Transitone type 3 - by R Radbill - 05-17-2023, 07:23 PM
RE: Transitone type 3 - by fenbach - 05-18-2023, 10:52 PM
RE: Transitone type 3 - by MrFixr55 - 05-19-2023, 12:14 AM
RE: Transitone type 3 - by R Radbill - 05-19-2023, 07:46 AM
RE: Transitone type 3 - by radiorich - 05-19-2023, 08:17 AM
RE: Transitone type 3 - by MrFixr55 - 05-21-2023, 09:04 AM
RE: Transitone type 3 - by R Radbill - 05-21-2023, 07:49 PM
RE: Transitone type 3 - by R Radbill - 05-21-2023, 07:52 PM
RE: Transitone type 3 - by MrFixr55 - 05-21-2023, 10:37 PM
RE: Transitone type 3 - by R Radbill - 05-21-2023, 10:41 PM
RE: Transitone type 3 - by Antipodal - 06-20-2023, 05:51 AM
RE: Transitone type 3 - by klondike98 - 06-21-2023, 01:53 PM
RE: Transitone type 3 - by wannchev - 07-07-2023, 01:41 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM
Looking for verification of correct schematic.
Klondike98, Thank you. I'll double check that SN and get back to you. GarySP, Thank you for the schematic.RossH — 12:13 AM
Looking for verification of correct schematic.
I think you have the correct take on your set. Ron's annotated early schematics that note the below B22000 serial numbe...klondike98 — 12:04 AM
Looking for verification of correct schematic.
Hello Ross. The Philco Radio Library located at the bottom of the page has the schematic with the tube count you have. ...GarySP — 10:48 PM
HiFi (Chifi) tube amp build - but my own design.
Tim It's be interesting if you put your schematic here. Who knows, you could get some advice from a few folks here. ...morzh — 10:01 PM

[-]
Who's Online
There are currently 1199 online users. [Complete List]
» 2 Member(s) | 1197 Guest(s)
AvatarAvatar

>