1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 42-716T shortwave problem
HooiserScootrer
Junior Member
**
Posts: 18
Threads: 6
Joined: Apr 2017
City: Noblesville, IN
#6

08-08-2023, 05:23 PM
Yep, did all that prior to posting. Today I noticed that moving one of the wires between the band switch and the antenna section of the tuner knocked out my generator signal.  I checked the wire for continuity while moving it and it checked good. On a whim, I pulled the tuner and replaced the mounting grommets, all wire and the braided ground leads.  After re-installing I had normal SW reception with a 20' indoor wire.  I think that's pretty good considering I'm in a basement with foil backed insulation and the radio doesn't have an RF amp.

Please note that several components listed on the schematic were not present in this radio.  This includes the 2.2M AVC resistor, cap #20 and mica caps 28C and 28D. I installed all of them.

Thanks to all who contributed.

Cheers,
Scott
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
RE: Philco 42-716T shortwave problem - by GarySP - 08-07-2023, 11:10 AM
RE: Philco 42-716T shortwave problem - by Chas - 08-07-2023, 07:13 PM
RE: Philco 42-716T shortwave problem - by HooiserScootrer - 08-08-2023, 05:23 PM



Users browsing this thread:
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently 2635 online users. [Complete List]
» 2 Member(s) | 2633 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration