Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

candohm section wattages
#3

YOu could do rough assessment.

You need to know the current. The assumption is that the current through the choke is the same that goes from the Ground back to the centertap of the rectifier.

The dropout across the choke is 85V at 1100 Ohm, making it 77mA. Let's make it 80 mA.
The total resistance of the "Candohm" is 192 Ohms. This makes it 1.14W total.
The dissipation on the sections is proportional to their resistances, so it will be 0.87W, 0.18W and 0.09W respectively.

Now triple the ratings: 3W, 0.5W and 0.25W for 146, 31 and 15 Ohms respectively. These are the ratings for the sections. Of course you could use large ratings. I usually go for triple where the circulation is good and no combustible material is nearby.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
candohm section wattages - by chradios - 09-02-2023, 12:41 PM
RE: candohm section wattages - by GarySP - 09-02-2023, 02:13 PM
RE: candohm section wattages - by morzh - 09-02-2023, 06:09 PM
RE: candohm section wattages - by chradios - 09-09-2023, 03:45 PM
RE: candohm section wattages - by radiorich - 09-09-2023, 08:45 PM
RE: candohm section wattages - by morzh - 09-09-2023, 08:49 PM
RE: candohm section wattages - by radiorich - 09-11-2023, 07:31 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>