1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Model 87
Chas
Senior Member
****
Posts: 706
Threads: 8
Joined: Apr 2018
City: S. Dartmouth State, Province, Country: MA
#13

09-06-2023, 05:17 PM
O.K!

Try the Simpson in AC mode across the primary of the output transformer, set for 100 volt scale more or less to start.

None the less, if your not getting any oscillation no matter where the dial is set, neutralization is good enough.

If either above below 1mhz is "less sensitive" when aligning the gang trimmers, move the calibration frequency up or down in the direction of the less sensitive area by about 30khz, more or less. That should balance out the sensitivity across the band. May have to neutralize a second time with that sort of compensation...

GL

Chas

Chas
Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco Model 87 - by fwmartin2000 - 08-29-2023, 08:28 PM
RE: Philco Model 87 - by MrFixr55 - 08-29-2023, 09:07 PM
RE: Philco Model 87 - by Radioroslyn - 08-29-2023, 09:17 PM
RE: Philco Model 87 - by morzh - 08-29-2023, 10:35 PM
RE: Philco Model 87 - by radiorich - 08-30-2023, 12:15 AM
RE: Philco Model 87 - by fwmartin2000 - 08-30-2023, 11:53 AM
RE: Philco Model 87 - by Radioroslyn - 08-30-2023, 12:19 PM
RE: Philco Model 87 - by morzh - 08-30-2023, 07:16 PM
RE: Philco Model 87 - by fwmartin2000 - 08-30-2023, 09:22 PM
RE: Philco Model 87 - by Chas - 08-30-2023, 11:43 PM
RE: Philco Model 87 - by morzh - 08-31-2023, 10:08 AM
RE: Philco Model 87 - by fwmartin2000 - 09-06-2023, 03:16 PM
RE: Philco Model 87 - by Chas - 09-06-2023, 05:17 PM
RE: Philco Model 87 - by fwmartin2000 - 09-07-2023, 08:51 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Mike; I've only run into a speaker with an open filed coil twice, and they were on newer speakers from the 1940s. One ...Arran — 12:48 AM
An attempt to remove the Field Coil from a G speaker
Arran Yes, this is my plan for now and what do I got to lose, this is not even the speaker from this radio, but one o...morzh — 10:44 PM
An attempt to remove the Field Coil from a G speaker
Mike;  I would unwrap the field coil, and see if maybe there a break near one of the ends, like where the coil wire att...Arran — 10:23 PM
An attempt to remove the Field Coil from a G speaker
...and this is what I did. I fed a little LT into the screwholes with a small brush, and a little on the rim next to the...morzh — 09:52 PM
Philco 40-120C Restoration
I combined the two 40-120C threads together as we like to keep the discussion of the same radio together. It helps with...klondike98 — 09:36 PM
Philco 40-120C Weak, Distorted Ouput
Just checked were I buy tubes price is four dollars. So living in Florid we have a local source for tubes. David    David — 09:14 PM
Philco 40-120C Weak, Distorted Ouput
The higher voltage may be due to higher mains voltage. My mains run 120-125AC when the set was new mains would be 110-11...David — 09:09 PM
Philco 40-120C Weak, Distorted Ouput
Thank you for your reply. I pulled a speaker from a Philco 41-221 and received the same result. I used a signal tracer t...bluecap — 08:45 PM
Philco 40-120C Weak, Distorted Ouput
Have you tried a different speaker? How did you trace the distortion? How do you know it is weak? What is the reference?...morzh — 08:33 PM
Philco 46-480 Electronic Restoration
Amen to that! Every time I think I’ve captured them all, I realize that there’s another error. My goal is to finish with...jrblasde — 07:00 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration