Restoring Philco model 87

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Restoring Philco model 87

wendell
Junior Member

Posts: 15
Threads: 3
Joined: Jun 2011

06-29-2011, 09:14 PM

Thanks Arran,

No, there's no terminal strip, everything is hardwired from point to point. This may be a blessing in disguise...I may just disconnect the filter block from the bottom and connect the new caps to the original wiring under the chassis. Thanks for the info about the 1619 tubes. What kind of adapters are you talking about? I'm very new at this..

Wendell

Find

« Next Oldest | Next Newest »

Messages In This Thread

Restoring Philco model 87 - by wendell - 06-24-2011, 09:35 PM

Re: Restoring Philco model 87 - by 7estatdef - 06-24-2011, 11:28 PM

Re: Restoring Philco model 87 - by wendell - 06-24-2011, 11:46 PM

Re: Restoring Philco model 87 - by 7estatdef - 06-25-2011, 07:21 AM

Another question about a model 87 - by wendell - 06-25-2011, 07:57 PM

Re: Restoring Philco model 87 - by 7estatdef - 06-25-2011, 10:53 PM

Re: Restoring Philco model 87 - by Arran - 06-29-2011, 08:25 PM

Re: Restoring Philco model 87 - by wendell - 06-29-2011, 09:14 PM

Re: Restoring Philco model 87 - by 7estatdef - 06-29-2011, 09:54 PM

Re: Restoring Philco model 87 - by Ron Ramirez - 06-30-2011, 08:06 AM

Re: Restoring Philco model 87 - by wendell - 06-30-2011, 09:57 AM

Re: Restoring Philco model 87 - by Ron Ramirez - 06-30-2011, 03:50 PM

Re: Restoring Philco model 87 - by Arran - 06-30-2011, 06:49 PM

Re: Restoring Philco model 87 - by Texasrocker - 07-01-2011, 09:22 PM

Re: Restoring Philco model 87 - by codefox1 - 07-01-2011, 11:09 PM

Re: Restoring Philco model 87 - by wendell - 07-08-2011, 10:37 AM

Re: Restoring Philco model 87 - by wendell - 07-08-2011, 10:48 AM

Re: Restoring Philco model 87 - by Ron Ramirez - 07-08-2011, 11:15 AM

Re: Restoring Philco model 87 - by wendell - 07-08-2011, 11:34 AM

Re: Restoring Philco model 87 - by 7estatdef - 07-11-2011, 03:06 PM

Re: Restoring Philco model 87 - by codefox1 - 07-11-2011, 03:41 PM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM
Philco 60 Squealing
Your IF transformers are tuned to the resonant frequency they were designed for. When you observe the bell curve they di...RodB — 01:35 PM
identify very thin wire for replacement on 37-640
Thanks so much for your help! I really could not have gotten this far without the kindness of you and other members. T...georgetownjohn — 11:50 AM

Who's Online

There are currently 3007 online users. [Complete List]
» 1 Member(s) | 3006 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me