Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Speaker Crud
#2

Well you could use a drift the drive the 4 fasteners out. Then you can lift the field coil assembly off of the basket. You'll probably will want to unsolder the voice coil and fc wires. Pull it straight up else you'll reck the vc as it's fitted down in the gap. The tough part is getting the fasteners back in. I would use a c clamp and socket to apply pressure to the head of it to press it back in place. Think about what you are doing before you do it... Be sure to keep the fc in place till your really to remove it. You don't want it bouncing around as it could deform or rip the vc out of the cone.

Once you get it apart you can clean the gap which probably full of dirt and dust with thin piece of plastic.

GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco Speaker Crud - by dconant - 11-05-2023, 02:14 PM
RE: Philco Speaker Crud - by Radioroslyn - 11-05-2023, 03:17 PM
RE: Philco Speaker Crud - by dconant - 11-06-2023, 08:12 AM
RE: Philco Speaker Crud - by Chas - 11-06-2023, 11:20 AM
RE: Philco Speaker Crud - by dconant - 11-06-2023, 11:35 AM
RE: Philco Speaker Crud - by Chas - 11-06-2023, 12:36 PM
RE: Philco Speaker Crud - by dconant - 11-06-2023, 01:05 PM
RE: Philco Speaker Crud - by Chas - 11-06-2023, 01:43 PM
RE: Philco Speaker Crud - by dconant - 11-06-2023, 01:54 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>