1953 Emerson 724

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

1953 Emerson 724

klondike98
Phorum Moderator

Posts: 5,084
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR

12-09-2023, 06:15 PM

Hey Rich thanks. I checked the clock today and while the rotor is moving the clock hands they are very slow so I will have to do the "refresh the rotor" procedure that I've been reading about. Two approaches that I've seen. 1) heat the rotor and have the oils seep out the gear opening and then put new oil in by slowly dripping it into the gear shaft opening or 2) drill a small hole in the case, suck out the old oil, rinse with solvent, and then add new oil. Seal up the hole with epoxy. Any suggestions welcome.

Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

1953 Emerson 724 - by klondike98 - 12-08-2023, 02:43 PM

RE: 1953 Emerson 724 - by David - 12-08-2023, 07:05 PM

RE: 1953 Emerson 724 - by klondike98 - 12-08-2023, 07:59 PM

RE: 1953 Emerson 724 - by radiorich - 12-08-2023, 09:01 PM

RE: 1953 Emerson 724 - by klondike98 - 12-09-2023, 06:15 PM

RE: 1953 Emerson 724 - by David - 12-09-2023, 10:16 PM

RE: 1953 Emerson 724 - by klondike98 - 12-13-2023, 09:47 PM

RE: 1953 Emerson 724 - by David - 12-14-2023, 01:50 PM

RE: 1953 Emerson 724 - by klondike98 - 12-16-2023, 12:02 AM

RE: 1953 Emerson 724 - by Paul Philco322 - 12-16-2023, 01:27 PM

RE: 1953 Emerson 724 - by klondike98 - 12-16-2023, 01:54 PM

RE: 1953 Emerson 724 - by GarySP - 12-16-2023, 03:17 PM

RE: 1953 Emerson 724 - by Eliot Ness - 12-19-2023, 09:24 PM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
Shadow Meter Bulb
Gary I doubt it would introduce any noise. We use similar lamps for the panel indication, 12V AC lamps: they are LEDs...morzh — 02:15 PM
Shadow Meter Bulb
Not sure if anyone has tried this but there are 6.3 volt miniature lamps in bayonet and screw-in base options available ...GarySP — 11:31 AM
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM

Who's Online

There are currently 8405 online users. [Complete List]
» 1 Member(s) | 8404 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me