Philco 37-61

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 37-61

7chip7
Junior Member

Posts: 35
Threads: 2
Joined: Dec 2023
City: Seaford State, Province, Country: DElaware

12-12-2023, 11:18 AM

I Have the chassis on the bench where I can do a better visual inspection. The top of the chassis is very dirty and dusty, but the underside is very clean, so I am going to get some of those bad caps replaced. I notice there are 2 block caps in this thing, so I will check the parts list to identify them. Its going to take some time to get this thing to the smoke test.
Thank you so much for the reply's, you folks are great
Regards Chip

The process of learning is to fix something that is not broke.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 37-61 - by 7chip7 - 12-11-2023, 09:04 PM

RE: Philco 37-61 - by Radioroslyn - 12-11-2023, 10:44 PM

RE: Philco 37-61 - by 7chip7 - 12-11-2023, 11:23 PM

RE: Philco 37-61 - by GarySP - 12-11-2023, 11:31 PM

RE: Philco 37-61 - by Radioroslyn - 12-12-2023, 01:11 AM

RE: Philco 37-61 - by 7chip7 - 12-12-2023, 11:18 AM

RE: Philco 37-61 - by klondike98 - 12-12-2023, 01:48 PM

RE: Philco 37-61 - by 7chip7 - 12-12-2023, 03:38 PM

RE: Philco 37-61 - by klondike98 - 12-13-2023, 02:01 PM

RE: Philco 37-61 - by MrFixr55 - 12-14-2023, 09:12 AM

RE: Philco 37-61 - by 7chip7 - 12-16-2023, 12:22 PM

RE: Philco 37-61 - by radiorich - 12-16-2023, 01:50 PM

RE: Philco 37-61 - by klondike98 - 12-16-2023, 05:44 PM

RE: Philco 37-61 - by 7chip7 - 12-18-2023, 11:27 AM

RE: Philco 37-61 - by 7chip7 - 12-18-2023, 11:47 AM

RE: Philco 37-61 - by David - 12-18-2023, 01:37 PM

RE: Philco 37-61 - by 7chip7 - 12-24-2023, 09:44 AM

RE: Philco 37-61 - by RodB - 12-24-2023, 10:33 AM

RE: Philco 37-61 - by Radioroslyn - 12-24-2023, 10:38 AM

RE: Philco 37-61 - by 7chip7 - 12-25-2023, 11:17 AM

RE: Philco 37-61 - by Radioroslyn - 12-25-2023, 03:03 PM

RE: Philco 37-61 - by RodB - 12-25-2023, 04:51 PM

RE: Philco 37-61 - by 7chip7 - 12-26-2023, 07:25 AM

RE: Philco 37-61 - by Radioroslyn - 12-26-2023, 10:17 AM

RE: Philco 37-61 - by 7chip7 - 12-26-2023, 11:29 AM

RE: Philco 37-61 - by Radioroslyn - 12-26-2023, 05:09 PM

RE: Philco 37-61 - by RodB - 12-26-2023, 08:48 PM

RE: Philco 37-61 - by 7chip7 - 12-27-2023, 08:08 AM

RE: Philco 37-61 - by 7chip7 - 12-30-2023, 08:22 AM

RE: Philco 37-61 - by Radioroslyn - 12-30-2023, 09:01 AM

RE: Philco 37-61 - by 7chip7 - 12-30-2023, 09:45 AM

RE: Philco 37-61 - by RodB - 12-30-2023, 09:49 AM

RE: Philco 37-61 - by 7chip7 - 12-30-2023, 02:03 PM

RE: Philco 37-61 - by 7chip7 - 12-30-2023, 04:30 PM

RE: Philco 37-61 - by RodB - 12-30-2023, 05:53 PM

RE: Philco 37-61 - by 7chip7 - 12-31-2023, 02:18 PM

RE: Philco 37-61 - by RodB - 01-01-2024, 12:03 PM

RE: Philco 37-61 - by Radioroslyn - 01-01-2024, 01:44 PM

RE: Philco 37-61 - by 7chip7 - 01-01-2024, 03:40 PM

37-61 Speaker Repair - by 7chip7 - 01-03-2024, 09:01 AM

View a Printable Version

Users browsing this thread: 8 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5494 online users. [Complete List]
» 2 Member(s) | 5492 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me