1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 89 Lower Frequencies
RodB
Phorum Expert
*****
Posts: 988
Threads: 40
Joined: Feb 2015
City: Roseville, MN
#13

12-16-2023, 10:11 PM
Hi Dan,

You have just described the reason, in just about every radio, there's at least one flat, braided wire, 1/4 to 1/3 Inch wide soldered between the stator and chassis. For oscillators and tuned rf circuits to run correctly there must be zero ohms at this point.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 89 Lower Frequencies - by dconant - 12-10-2023, 03:08 PM
RE: Philco 89 Lower Frequencies - by klondike98 - 12-10-2023, 05:33 PM
RE: Philco 89 Lower Frequencies - by MrFixr55 - 12-11-2023, 09:06 AM
RE: Philco 89 Lower Frequencies - by dconant - 12-11-2023, 09:27 AM
RE: Philco 89 Lower Frequencies - by Radioroslyn - 12-11-2023, 10:28 AM
RE: Philco 89 Lower Frequencies - by dconant - 12-11-2023, 12:07 PM
RE: Philco 89 Lower Frequencies - by dconant - 12-11-2023, 01:17 PM
RE: Philco 89 Lower Frequencies - by dconant - 12-11-2023, 04:42 PM
RE: Philco 89 Lower Frequencies - by dconant - 12-11-2023, 06:06 PM
RE: Philco 89 Lower Frequencies - by Radioroslyn - 12-11-2023, 08:45 PM
RE: Philco 89 Lower Frequencies - by dconant - 12-16-2023, 07:06 PM
RE: Philco 89 Lower Frequencies - by Radioroslyn - 12-16-2023, 10:10 PM
RE: Philco 89 Lower Frequencies - by RodB - 12-16-2023, 10:11 PM
RE: Philco 89 Lower Frequencies - by dconant - 12-17-2023, 09:55 AM
RE: Philco 89 Lower Frequencies - by RodB - 12-17-2023, 11:01 AM
RE: Philco 89 Lower Frequencies - by dconant - 12-17-2023, 11:12 AM
RE: Philco 89 Lower Frequencies - by Radioroslyn - 12-17-2023, 02:42 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration