Fred's job on the RCA140

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Fred's job on the RCA140

morzh
Odobenus rosmarus

Posts: 15,704
Threads: 551
Joined: Oct 2011
City: Jackson, NJ

#17

01-06-2024, 09:42 AM

Fred is sure one of very few folks who does this level of restoration.
I could safely put Steve Davis and Russ Webb in the same category.

I wish one of them would taught a several-days seminar on Introduction to woodworking and radio cabinet restoration. I would sure try to attend. I am not even a beginner, I simply do not restore wood.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Fred's job on the RCA140 - by morzh - 01-03-2024, 09:52 PM

RE: Fred's job on the RCA140 - by morzh - 01-03-2024, 09:53 PM

RE: Fred's job on the RCA140 - by Paul Philco322 - 01-03-2024, 09:54 PM

RE: Fred's job on the RCA140 - by radiorich - 01-03-2024, 10:09 PM

RE: Fred's job on the RCA140 - by morzh - 01-03-2024, 10:12 PM

RE: Fred's job on the RCA140 - by Eliot Ness - 01-04-2024, 01:13 AM

RE: Fred's job on the RCA140 - by morzh - 01-04-2024, 08:01 AM

RE: Fred's job on the RCA140 - by WyTex - 01-04-2024, 08:30 AM

RE: Fred's job on the RCA140 - by morzh - 01-04-2024, 10:24 AM

RE: Fred's job on the RCA140 - by Eliot Ness - 01-04-2024, 10:28 AM

RE: Fred's job on the RCA140 - by morzh - 01-04-2024, 10:41 AM

RE: Fred's job on the RCA140 - by WyTex - 01-04-2024, 04:33 PM

RE: Fred's job on the RCA140 - by Paul Philco322 - 01-04-2024, 09:52 PM

RE: Fred's job on the RCA140 - by fenbach - 01-05-2024, 12:59 AM

RE: Fred's job on the RCA140 - by morzh - 01-05-2024, 12:44 PM

RE: Fred's job on the RCA140 - by slford310 - 01-05-2024, 09:00 PM

RE: Fred's job on the RCA140 - by morzh - 01-06-2024, 09:42 AM

RE: Fred's job on the RCA140 - by slford310 - 01-06-2024, 09:59 AM

RE: Fred's job on the RCA140 - by morzh - 01-06-2024, 11:06 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic. As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

Who's Online

There are currently 3986 online users. [Complete List]
» 1 Member(s) | 3985 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me