1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco alignment tool ?
DaleHCook
Philco, Zenith, and Howard Phan
***
Posts: 161
Threads: 8
Joined: Apr 2023
City: Roanoke State, Province, Country: Virginia
#3

02-21-2024, 10:05 AM
What size are the nuts? IIRC I have seen some old (40 years or so) alignment tool sets (possibly GC) that had what were essentially plastic nutdrivers.
Dale H. Cook, GR/HP/Tek Collector, Roanoke/Lynchburg, VA
https://plymouthcolony.net/starcity/radios/
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
philco alignment tool ? - by aSamuel - 02-20-2024, 07:14 PM
RE: philco alignment tool ? - by morzh - 02-21-2024, 10:05 AM
RE: philco alignment tool ? - by DaleHCook - 02-21-2024, 10:05 AM
RE: philco alignment tool ? - by Eliot Ness - 02-21-2024, 07:57 PM
RE: philco alignment tool ? - by Steve Davis - 02-21-2024, 09:10 PM
RE: philco alignment tool ? - by morzh - 02-21-2024, 10:26 PM
RE: philco alignment tool ? - by klondike98 - 02-22-2024, 02:17 AM
RE: philco alignment tool ? - by tym - 02-22-2024, 01:56 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5356 online users. [Complete List]
» 1 Member(s) | 5355 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration