1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Signal Generator Help Needed
SRv2
Junior Member
**
Posts: 27
Threads: 5
Joined: Mar 2024
City: BERTHOUD State, Province, Country: CO
#10

03-27-2024, 09:01 PM
Thanks for the feedback and help. I have a new (old) isolation transformer on order. And I’ll use a 10 nf cap. I’m slowly getting my bench built back up, 40 years later. Blowing the cobwebs off my memory, so I do appreciate the help.  George
George - Berthoud, Colorado.  Learned tube receiver repair and troubleshooting in the Navy way back when, came back around to it as an old guy.  Re-learning all I can.  Doing my part to restore a few of these old gems.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Signal Generator Help Needed - by SRv2 - 03-24-2024, 05:23 PM
RE: Signal Generator Help Needed - by DaleHCook - 03-25-2024, 05:32 AM
RE: Signal Generator Help Needed - by SRv2 - 03-25-2024, 07:40 AM
RE: Signal Generator Help Needed - by DaleHCook - 03-25-2024, 08:02 AM
462ron - by 462ron - 03-25-2024, 08:04 AM
RE: Signal Generator Help Needed - by SRv2 - 03-25-2024, 08:17 AM
RE: Signal Generator Help Needed - by morzh - 03-26-2024, 08:07 PM
RE: Signal Generator Help Needed - by SRv2 - 03-26-2024, 09:02 PM
RE: Signal Generator Help Needed - by morzh - 03-27-2024, 07:41 PM
RE: Signal Generator Help Needed - by SRv2 - 03-27-2024, 09:01 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Today I've been reading through the site trying to learn more about this radio. I also soldered the lose power cord cabl...osanders0311 — 08:24 PM
Philco 610B oscillator wiring
Thanks David! I do have that same later prodution model 610 schematic. I've also studied the Philco service bulletins fo...Tubester — 08:12 PM
Philco 610B oscillator wiring
Some info from Beitmans says late production. David   David — 06:06 PM
Restoring Philco 96
Oh wow! Just found this thread.  Brings me back to early days on this phorum.  I did a 96 back in 2017.  Thread here: ...rfeenstra — 06:05 PM
Philco 610B oscillator wiring
Thanks for the replies. It's not the really the hum that I am after. Just trying to understand why only the shortwave ba...Tubester — 04:01 PM
Restoring Philco 96
70 and 90 are Superhets, but at least the 2x45 model of 90 uses the Plate detector (and so does 70). Also the Atwaters,...morzh — 03:28 PM
Restoring Philco 96
Morzh, Prayers for your mom. I am sure that there was enough pain living through the Holocaust as a child. I pray dail...MrFixr55 — 02:19 PM
Philco 610B oscillator wiring
Hi Dan, Divide and conquer. First off trry to differentiate between 60Hz and 120 Hz hum. 120 Hz hum has a higher pit...MrFixr55 — 01:49 PM
Restoring Philco 96
Yes, other than takin a toll on your back, they are undeed way more repair friendly than many other Philcos. To me, som...morzh — 01:04 PM
Philco 610B oscillator wiring
If the wires look like they were this way from the factory (very neat and very dull soldering joints), I'd leave them be...morzh — 12:58 PM

[-]
Who's Online
There are currently 2844 online users. [Complete List]
» 1 Member(s) | 2843 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment