Model 50A rebuild

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Model 50A rebuild

GarySP
Super Moderator

Posts: 1,975
Threads: 147
Joined: Jan 2013
City: Westland, MI

04-08-2024, 08:43 PM

Welcome to the Phorum, Mtmattking! The bakelite enclosures are fairly easy to gut and refill with new caps. You don't have to repot with glue since they wont be seen being mounted against the chassis. Several others have documented their rebuilds. I'm sure they will chime in. Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan

Find

« Next Oldest | Next Newest »

Messages In This Thread

Model 50A rebuild - by Mtmattking - 04-08-2024, 07:19 PM

RE: Model 50A rebuild - by GarySP - 04-08-2024, 08:43 PM

RE: Model 50A rebuild - by morzh - 04-08-2024, 09:30 PM

RE: Model 50A rebuild - by Mtmattking - 04-08-2024, 09:35 PM

RE: Model 50A rebuild - by Mtmattking - 04-08-2024, 09:37 PM

RE: Model 50A rebuild - by klondike98 - 04-08-2024, 09:51 PM

RE: Model 50A rebuild - by Mtmattking - 04-08-2024, 09:57 PM

RE: Model 50A rebuild - by klondike98 - 04-09-2024, 03:20 AM

RE: Model 50A rebuild - by Mtmattking - 04-09-2024, 10:56 PM

RE: Model 50A rebuild - by morzh - 04-11-2024, 08:01 AM

RE: Model 50A rebuild - by Mtmattking - 06-29-2024, 09:58 PM

RE: Model 50A rebuild - by morzh - 06-30-2024, 11:07 AM

RE: Model 50A rebuild - by Mtmattking - 06-30-2024, 12:41 PM

RE: Model 50A rebuild - by morzh - 06-30-2024, 01:16 PM

RE: Model 50A rebuild - by GarySP - 06-30-2024, 04:25 PM

RE: Model 50A rebuild - by Mtmattking - 07-06-2024, 08:26 PM

RE: Model 50A rebuild - by morzh - 07-06-2024, 10:20 PM

RE: Model 50A rebuild - by Mtmattking - 07-07-2024, 01:00 AM

RE: Model 50A rebuild - by RodB - 07-07-2024, 09:24 AM

RE: Model 50A rebuild - by Chas - 07-07-2024, 09:50 AM

RE: Model 50A rebuild - by Paul Philco322 - 07-07-2024, 01:19 PM

RE: Model 50A rebuild - by GarySP - 07-07-2024, 03:19 PM

RE: Model 50A rebuild - by morzh - 07-07-2024, 07:33 PM

RE: Model 50A rebuild - by Mtmattking - 07-15-2024, 01:02 PM

RE: Model 50A rebuild - by Mtmattking - 07-20-2024, 10:28 PM

RE: Model 50A rebuild - by Radioroslyn - 07-22-2024, 09:29 AM

RE: Model 50A rebuild - by Mtmattking - 07-22-2024, 07:10 PM

RE: Model 50A rebuild - by Radioroslyn - 07-23-2024, 07:58 AM

RE: Model 50 Capacitor values - by Mtmattking - 04-08-2024, 10:39 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

Who's Online

There are currently 3382 online users. [Complete List]
» 1 Member(s) | 3381 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me