Model 50A rebuild

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Model 50A rebuild

Mtmattking
Junior Member

Posts: 17
Threads: 2
Joined: Nov 2022
City: Victoria State, Province, Country: BC

#17

07-06-2024, 08:26 PM

Thank for the explanation on the EM shield. This makes sense

I pulled off my variable cap and cleaned it. Now I have lost all reception but I still have an AC hum.

Any ideas?

I did note that both sides of my variable cap has both sets of plates when I reinstalled it. Is this normal for this circuit?

Thank you

Find

« Next Oldest | Next Newest »

Messages In This Thread

Model 50A rebuild - by Mtmattking - 04-08-2024, 07:19 PM

RE: Model 50A rebuild - by GarySP - 04-08-2024, 08:43 PM

RE: Model 50A rebuild - by morzh - 04-08-2024, 09:30 PM

RE: Model 50A rebuild - by Mtmattking - 04-08-2024, 09:35 PM

RE: Model 50A rebuild - by Mtmattking - 04-08-2024, 09:37 PM

RE: Model 50A rebuild - by klondike98 - 04-08-2024, 09:51 PM

RE: Model 50A rebuild - by Mtmattking - 04-08-2024, 09:57 PM

RE: Model 50A rebuild - by klondike98 - 04-09-2024, 03:20 AM

RE: Model 50A rebuild - by Mtmattking - 04-09-2024, 10:56 PM

RE: Model 50A rebuild - by morzh - 04-11-2024, 08:01 AM

RE: Model 50A rebuild - by Mtmattking - 06-29-2024, 09:58 PM

RE: Model 50A rebuild - by morzh - 06-30-2024, 11:07 AM

RE: Model 50A rebuild - by Mtmattking - 06-30-2024, 12:41 PM

RE: Model 50A rebuild - by morzh - 06-30-2024, 01:16 PM

RE: Model 50A rebuild - by GarySP - 06-30-2024, 04:25 PM

RE: Model 50A rebuild - by Mtmattking - 07-06-2024, 08:26 PM

RE: Model 50A rebuild - by morzh - 07-06-2024, 10:20 PM

RE: Model 50A rebuild - by Mtmattking - 07-07-2024, 01:00 AM

RE: Model 50A rebuild - by RodB - 07-07-2024, 09:24 AM

RE: Model 50A rebuild - by Chas - 07-07-2024, 09:50 AM

RE: Model 50A rebuild - by Paul Philco322 - 07-07-2024, 01:19 PM

RE: Model 50A rebuild - by GarySP - 07-07-2024, 03:19 PM

RE: Model 50A rebuild - by morzh - 07-07-2024, 07:33 PM

RE: Model 50A rebuild - by Mtmattking - 07-15-2024, 01:02 PM

RE: Model 50A rebuild - by Mtmattking - 07-20-2024, 10:28 PM

RE: Model 50A rebuild - by Radioroslyn - 07-22-2024, 09:29 AM

RE: Model 50A rebuild - by Mtmattking - 07-22-2024, 07:10 PM

RE: Model 50A rebuild - by Radioroslyn - 07-23-2024, 07:58 AM

RE: Model 50 Capacitor values - by Mtmattking - 04-08-2024, 10:39 PM

View a Printable Version

Users browsing this thread: 5 Guest(s)

Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

Who's Online

There are currently 7268 online users. [Complete List]
» 3 Member(s) | 7265 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me