Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Jr.
#11

For that cap block I used a .01uF Y2 safety cap but as you can see in my first picture the electrolytic cap you are referring to does not exist in my chassis.

As to progress, I have already rebuilt the blocks and replaced resistors that were OOT but I am waiting on a replacement resistor for the 16K (#11) to get here from Digikey which should be Monday. Then I can complete installing the second filter cap and the 16K and 1M resistors.

As for the gimmick around the wire from the volume control center tap, how tight do the windings need to be or does it not matter?


Messages In This Thread
Philco Jr. - by Jim Dutridge - 07-22-2024, 02:56 PM
RE: Philco Jr. - by Jim Dutridge - 07-22-2024, 06:00 PM
RE: Philco Jr. - by Ed Locker - 07-23-2024, 10:16 AM
RE: Philco Jr. - by Jim Dutridge - 07-23-2024, 11:51 AM
RE: Philco Jr. - by Jim Dutridge - 07-23-2024, 12:35 PM
RE: Philco Jr. - by Radioroslyn - 07-23-2024, 05:59 PM
RE: Philco Jr. - by Jim Dutridge - 07-23-2024, 07:33 PM
RE: Philco Jr. - by David - 07-23-2024, 08:35 PM
RE: Philco Jr. - by David - 07-23-2024, 08:40 PM
RE: Philco Jr. - by Radioroslyn - 07-23-2024, 09:44 PM
RE: Philco Jr. - by Jim Dutridge - 07-28-2024, 12:10 PM
RE: Philco Jr. - by Radioroslyn - 07-28-2024, 04:34 PM
RE: Philco Jr. - by Jim Dutridge - 07-29-2024, 08:55 AM
RE: Philco Jr. - by Radioroslyn - 07-29-2024, 04:14 PM
RE: Philco Jr. - by Jim Dutridge - 07-29-2024, 04:38 PM
RE: Philco Jr. - by Jim Dutridge - 07-31-2024, 04:21 PM
RE: Philco Jr. - by David - 07-31-2024, 07:59 PM
RE: Philco Jr. - by Radioroslyn - 07-31-2024, 10:00 PM
RE: Philco Jr. - by Jim Dutridge - 08-02-2024, 04:08 PM
RE: Philco Jr. - by Jim Dutridge - 08-09-2024, 02:53 PM
RE: Philco Jr. - by RodB - 08-09-2024, 08:39 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

[-]
Who's Online
There are currently 6335 online users. [Complete List]
» 3 Member(s) | 6332 Guest(s)
AvatarAvatarAvatar

>