Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 89B code 123 newbie
#9

I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1" pvc pipe fits the bill at 1.315" od. Sometimes you can find some short pieces at the store for cheep. A good sanding to breakdown the slick finish on the outside will help the silver paint stick. Primer helps even more it's made for pvc stuff. A couple of end caps and something for the bottom. You could use hot glue to hold it in place (the bottom cap). That's if you want to go this route...

The last time Mershon caps were used in Philco chassis was in the 1931/32. So, you wouldn't really find copper caps in the 89/19 models. For what it's worth.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco 89B code 123 newbie - by Kurt P - 09-13-2024, 02:44 AM
RE: Philco 89B code 123 newbie - by radiorich - 09-13-2024, 08:12 AM
RE: Philco 89B code 123 newbie - by MrFixr55 - 09-13-2024, 09:36 AM
RE: Philco 89B code 123 newbie - by Kurt P - 09-23-2024, 04:43 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 09-23-2024, 09:46 PM
RE: Philco 89B code 123 newbie - by MrFixr55 - 09-24-2024, 06:06 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 09-24-2024, 09:25 PM
RE: Philco 89B code 123 newbie - by MrFixr55 - 09-24-2024, 10:07 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 09-25-2024, 10:28 AM
RE: Philco 89B code 123 newbie - by Kurt P - 09-27-2024, 05:35 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 09-27-2024, 08:50 PM
RE: Philco 89B code 123 newbie - by MrFixr55 - 09-28-2024, 09:03 AM
RE: Philco 89B code 123 newbie - by Kurt P - 10-15-2024, 03:07 PM
RE: Philco 89B code 123 newbie - by Kurt P - 10-18-2024, 01:30 PM
RE: Philco 89B code 123 newbie - by RodB - 10-18-2024, 03:29 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 10-18-2024, 05:15 PM
Kurt P - by Kurt P - 10-19-2024, 11:59 AM
RE: Philco 89B code 123 newbie - by Kurt P - 10-21-2024, 08:25 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 10-22-2024, 11:25 AM
RE: Philco 89B code 123 newbie - by Kurt P - 11-06-2024, 09:04 PM
RE: Philco 89B code 123 newbie - by morzh - 11-06-2024, 10:55 PM
RE: Philco 89B code 123 newbie - by MrFixr55 - 11-06-2024, 10:57 PM
RE: Philco 89B code 123 newbie - by Kurt P - 11-09-2024, 03:42 PM
RE: Philco 89B code 123 newbie - by MrFixr55 - 11-09-2024, 04:26 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 60 restoration
Mike; So if you check the resistance from end to end the volume pot reads 3 meg Ohm? I could see 1 meg maybe, if some...Arran — 11:59 PM
40-180 electrical troubleshooting
I isolated the circuit. And I’m still blowing 60 resistor. I just ordered the 84 rectifier tube. To see if that’s the is...winamp920@yahoo.com — 10:58 PM
Philco 60 restoration
After having attached the line cord, I checked the switch and the volume pot again. That is, I did check the switch befo...morzh — 10:34 PM
The list of my radio & TV collection!
Interesting. A suitcase itself might've been the Zenith's idea; their Transoceanic was a suitcase. Even if not the type...morzh — 06:40 PM
The list of my radio & TV collection!
Hi Michael. I think it's possible that it's the other way around - a previous model of this radio, which was developed b...RadioSvit — 06:15 PM
My first Philco radio.
It's unrelated and totally off on a tangent.Oldie Goldie — 05:13 PM
The list of my radio & TV collection!
I wonder if the Telefunken portable was some inspiration for this one.morzh — 05:12 PM
Custom Hammond Power Transformer
Heyboer do greta job; it's just at some point someone here said they quit doing custom orders. They did two transformer...morzh — 04:49 PM
My first Philco radio.
I wonder which dictionary he looked in :lol:morzh — 04:44 PM
Custom Hammond Power Transformer
Alright, I feel like a dummy at this point. I moved the transformer to a different surface and plugged it back in. This ...jrblasde — 04:39 PM

[-]
Who's Online
There are currently no members online.

>