Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 89B code 123 newbie
#16

The flat copper wires are from the hum bucking coil. All of the other resistances seem to be OK.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco 89B code 123 newbie - by Kurt P - 09-13-2024, 02:44 AM
RE: Philco 89B code 123 newbie - by radiorich - 09-13-2024, 08:12 AM
RE: Philco 89B code 123 newbie - by MrFixr55 - 09-13-2024, 09:36 AM
RE: Philco 89B code 123 newbie - by Kurt P - 09-23-2024, 04:43 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 09-23-2024, 09:46 PM
RE: Philco 89B code 123 newbie - by MrFixr55 - 09-24-2024, 06:06 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 09-24-2024, 09:25 PM
RE: Philco 89B code 123 newbie - by MrFixr55 - 09-24-2024, 10:07 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 09-25-2024, 10:28 AM
RE: Philco 89B code 123 newbie - by Kurt P - 09-27-2024, 05:35 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 09-27-2024, 08:50 PM
RE: Philco 89B code 123 newbie - by MrFixr55 - 09-28-2024, 09:03 AM
RE: Philco 89B code 123 newbie - by Kurt P - 10-15-2024, 03:07 PM
RE: Philco 89B code 123 newbie - by Kurt P - 10-18-2024, 01:30 PM
RE: Philco 89B code 123 newbie - by RodB - 10-18-2024, 03:29 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 10-18-2024, 05:15 PM
Kurt P - by Kurt P - 10-19-2024, 11:59 AM
RE: Philco 89B code 123 newbie - by Kurt P - 10-21-2024, 08:25 PM
RE: Philco 89B code 123 newbie - by Radioroslyn - 10-22-2024, 11:25 AM
RE: Philco 89B code 123 newbie - by Kurt P - 11-06-2024, 09:04 PM
RE: Philco 89B code 123 newbie - by morzh - 11-06-2024, 10:55 PM
RE: Philco 89B code 123 newbie - by MrFixr55 - 11-06-2024, 10:57 PM
RE: Philco 89B code 123 newbie - by Kurt P - 11-09-2024, 03:42 PM
RE: Philco 89B code 123 newbie - by MrFixr55 - 11-09-2024, 04:26 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
My first Philco radio.
Using brass go to the range look at different spent shell casing find one the right size then cut to length. DavidDavid — 10:34 PM
My first Philco radio.
Only thing I can think of is using something tougher for shim material like very thin steel or brass? Whatever soft gar...Oldie Goldie — 10:18 PM
My first Philco radio.
morzh, yeah that's basically the same shaft I have. Your probably right, that the ball bearings have gouged a groove so...Oldie Goldie — 10:09 PM
My first Philco radio.
Ok I took a tea candle and used it's metal cup for thin shim material. Cut a long straight piece and put it inside the c...Oldie Goldie — 09:34 PM
Philco 49-607 inop
1U5 is not a power tube. It does indeed have a diode in it, but this is a detector type and not a power rectifier. The ...morzh — 08:57 PM
Philco 49-607 inop
I was able to borrow a tube tester and my 117z3 is good. It glowed when I applied voltage to it as it had in the radio. ...Tennangler — 08:34 PM
Custom Hammond Power Transformer
...or one might keep checking eBay, swapmeets. Power xfmrs from Philco often pop up. And though the price of them is som...morzh — 08:31 PM
My first Philco radio.
OK, found it. Ron's 37-640. The last page Is this the gear? PS. If it keeps doing it, maybe the balls have worn out...morzh — 08:27 PM
My first Philco radio.
The inner shaft should snap in place. Mr. Fixr, sorry did not see your post, so omine was redundant.morzh — 08:19 PM
My first Philco radio.
Circlip, c-clip, e-clip, snap ring - all types of the retaining ring. Also called "Jesus clip". The reason bei...morzh — 08:18 PM

[-]
Who's Online
There are currently 1966 online users. [Complete List]
» 2 Member(s) | 1964 Guest(s)
AvatarAvatar

>