1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
48-1262 record changer problem
ETS1979
Junior Member
**
Posts: 12
Threads: 2
Joined: Jul 2011
#11

07-30-2011, 02:52 PM
I used a clip lead to temporarily connect the yellow wire to the switch. I connected the bare wire to test point "B" as described in the 48-1262 troubleshooting guide as shown in the Section 1 drawing. Did I connect it correctly? As suggested would probably happen after I powered the unit up, there was a loud buzz/hum in the turntable section. The radio remained clean. Touching the stylus with my finger varied the intensity of the hum. Any suggestions on the best way to safely remove the cartridge and where to send it to be rebuilt?
Find
« Next Oldest | Next Newest »


Messages In This Thread
48-1262 record changer problem - by ETS1979 - 07-21-2011, 07:04 PM
Re: 48-1262 record changer problem - by ETS1979 - 07-26-2011, 06:17 PM
Re: 48-1262 record changer problem - by ETS1979 - 07-27-2011, 08:03 AM
Re: 48-1262 record changer problem - by ETS1979 - 07-27-2011, 05:45 PM
Re: 48-1262 record changer problem - by ETS1979 - 07-30-2011, 11:16 AM
Re: 48-1262 record changer problem - by ETS1979 - 07-30-2011, 11:18 AM
Re: 48-1262 record changer problem - by codefox1 - 07-30-2011, 11:40 AM
Re: 48-1262 record changer problem - by ETS1979 - 07-30-2011, 02:52 PM
Re: 48-1262 record changer problem - by codefox1 - 07-30-2011, 04:33 PM
Re: 48-1262 record changer problem - by ETS1979 - 08-23-2011, 09:08 PM
Re: 48-1262 record changer problem - by ETS1979 - 09-02-2011, 06:07 PM
Re: 48-1262 record changer problem - by ETS1979 - 09-09-2011, 07:49 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently 2888 online users. [Complete List]
» 1 Member(s) | 2887 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration