Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-2 Low Volume
#5

Thanks guys for the help. I started looking at these points but I have to quit for the day. I will be looking into this stuff more Monday.


Messages In This Thread
Philco 38-2 Low Volume - by dconant - 11-09-2024, 02:27 PM
RE: Philco 38-2 Low Volume - by morzh - 11-09-2024, 03:15 PM
RE: Philco 38-2 Low Volume - by MrFixr55 - 11-09-2024, 10:27 PM
RE: Philco 38-2 Low Volume - by RodB - 11-10-2024, 11:44 AM
RE: Philco 38-2 Low Volume - by dconant - 11-10-2024, 01:23 PM
RE: Philco 38-2 Low Volume - by dconant - 11-10-2024, 02:39 PM
RE: Philco 38-2 Low Volume - by morzh - 11-10-2024, 03:25 PM
RE: Philco 38-2 Low Volume - by MrFixr55 - 11-10-2024, 06:31 PM
RE: Philco 38-2 Low Volume - by RodB - 11-10-2024, 06:52 PM
RE: Philco 38-2 Low Volume - by morzh - 11-10-2024, 07:16 PM
RE: Philco 38-2 Low Volume - by dconant - Yesterday, 12:05 PM
RE: Philco 38-2 Low Volume - by RodB - Yesterday, 01:17 PM
RE: Philco 38-2 Low Volume - by dconant - Yesterday, 02:06 PM
RE: Philco 38-2 Low Volume - by dconant - Yesterday, 02:14 PM
RE: Philco 38-2 Low Volume - by RodB - Yesterday, 02:36 PM
RE: Philco 38-2 Low Volume - by dconant - Yesterday, 03:50 PM
RE: Philco 38-2 Low Volume - by dconant - Yesterday, 04:58 PM
RE: Philco 38-2 Low Volume - by RodB - Yesterday, 05:20 PM
RE: Philco 38-2 Low Volume - by RodB - Yesterday, 05:38 PM
RE: Philco 38-2 Low Volume - by dconant - Yesterday, 06:23 PM
RE: Philco 38-2 Low Volume - by RodB - Yesterday, 11:15 PM
RE: Philco 38-2 Low Volume - by dconant - Today, 08:51 AM
RE: Philco 38-2 Low Volume - by RodB - 10 hours ago
RE: Philco 38-2 Low Volume - by morzh - 10 hours ago
RE: Philco 38-2 Low Volume - by RodB - 9 hours ago



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Newbie questions RE: Philco 41-608
John Thank you for the detailed response. I checked my connection again based on the schematic and your suggestions....tmurphy — 08:42 PM
Philco 38-2 Low Volume
Hi MrFixr55, The aux sound was good and yes it can be made too loud. The tone has no real effect on volume just tone, ge...dconant — 06:04 PM
RF Choke and Condenser -42-PT-7
Hi Folks, If you are talking about Part #7, this is the cap that capacitively grounds the physical chassis to B- and...MrFixr55 — 06:04 PM
Photo-finish repair
Thanks for the reply Bob.  I think I will try the touchup process.  Do you have any suggestions on what I should use to ...georgetownjohn — 05:52 PM
Philco 38-2 Low Volume
Hi DConant, I don't think that the extra 0.7 MOhm would make much difference. If the pot was supposed to be a 500KOhm...MrFixr55 — 05:21 PM
Photo-finish repair
Welcome to the Phorum! :wave: Once upon a time there was a supplier for some photofinish decals but no longer that I...klondike98 — 05:21 PM
Philco 38-2 Low Volume
Hi MrFixr55, Thank you for the drawing. I can handle that. I disconnected the muting switch from the center pin of the p...dconant — 04:50 PM
Philco 38-2 Low Volume
Sorry, I did not see your post as I was writing mine. I would think that with a consumer electronics level Aux input of...MrFixr55 — 04:24 PM
Philco 38-2 Low Volume
HI DConat, It wouldn't hurt to put a 0.01 uF cap between the deck and volume control.  However, there is a 0.01uF cap b...MrFixr55 — 02:57 PM
Philco 38-2 Low Volume
I connected my tape deck to the pot as stated with a .01 cap between. Volume is still low. Maybe I am expecting too much...dconant — 02:57 PM

[-]
Who's Online
There are currently 985 online users. [Complete List]
» 5 Member(s) | 980 Guest(s)
AvatarAvatarAvatarAvatar
Avatar

>