Philco 38-2 Low Volume

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 38-2 Low Volume

dconant
Member

Posts: 130
Threads: 25
Joined: Jun 2022
City: Marion State, Province, Country: NY

#16

11-11-2024, 03:50 PM

No I'm not sure where you are going other than check my work which I have been doing. Did you notice I said there is a 60 volt drop across the field coil? Is this normal? I disconnected 14X and still at 235 volts on the B+ side of that resistor. Also when I did my initial IF alignment I could not get 1XC to peak. It did get louder as I screwed it in but it never dropped off and it is almost all the way in now. Does this mean anything?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 38-2 Low Volume - by dconant - 11-09-2024, 02:27 PM

RE: Philco 38-2 Low Volume - by morzh - 11-09-2024, 03:15 PM

RE: Philco 38-2 Low Volume - by MrFixr55 - 11-09-2024, 10:27 PM

RE: Philco 38-2 Low Volume - by RodB - 11-10-2024, 11:44 AM

RE: Philco 38-2 Low Volume - by dconant - 11-10-2024, 01:23 PM

RE: Philco 38-2 Low Volume - by dconant - 11-10-2024, 02:39 PM

RE: Philco 38-2 Low Volume - by morzh - 11-10-2024, 03:25 PM

RE: Philco 38-2 Low Volume - by MrFixr55 - 11-10-2024, 06:31 PM

RE: Philco 38-2 Low Volume - by RodB - 11-10-2024, 06:52 PM

RE: Philco 38-2 Low Volume - by morzh - 11-10-2024, 07:16 PM

RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 12:05 PM

RE: Philco 38-2 Low Volume - by RodB - 11-11-2024, 01:17 PM

RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 02:06 PM

RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 02:14 PM

RE: Philco 38-2 Low Volume - by RodB - 11-11-2024, 02:36 PM

RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 03:50 PM

RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 04:58 PM

RE: Philco 38-2 Low Volume - by RodB - 11-11-2024, 05:20 PM

RE: Philco 38-2 Low Volume - by RodB - 11-11-2024, 05:38 PM

RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 06:23 PM

RE: Philco 38-2 Low Volume - by RodB - 11-11-2024, 11:15 PM

RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 08:51 AM

RE: Philco 38-2 Low Volume - by RodB - 11-12-2024, 10:53 AM

RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 11:02 AM

RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 11:16 AM

RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 11:22 AM

RE: Philco 38-2 Low Volume - by RodB - 11-12-2024, 11:43 AM

RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 11:52 AM

RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 11:57 AM

RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 12:02 PM

RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 12:08 PM

RE: Philco 38-2 Low Volume - by MrFixr55 - 11-12-2024, 12:27 PM

RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 12:42 PM

RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 02:07 PM

RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 02:25 PM

RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 02:57 PM

RE: Philco 38-2 Low Volume - by MrFixr55 - 11-12-2024, 02:57 PM

RE: Philco 38-2 Low Volume - by MrFixr55 - 11-12-2024, 04:24 PM

RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 04:50 PM

RE: Philco 38-2 Low Volume - by MrFixr55 - 11-12-2024, 05:21 PM

RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 06:04 PM

RE: Philco 38-2 Low Volume - by dconant - 11-13-2024, 04:08 PM

RE: Philco 38-2 Low Volume - by morzh - 11-13-2024, 04:37 PM

RE: Philco 38-2 Low Volume - by dconant - 11-13-2024, 04:42 PM

RE: Philco 38-2 Low Volume - by morzh - 11-13-2024, 04:52 PM

RE: Philco 38-2 Low Volume - by dconant - 11-13-2024, 04:56 PM

RE: Philco 38-2 Low Volume - by morzh - 11-13-2024, 05:22 PM

RE: Philco 38-2 Low Volume - by dconant - 11-13-2024, 06:03 PM

RE: Philco 38-2 Low Volume - by MrFixr55 - 11-13-2024, 06:51 PM

RE: Philco 38-2 Low Volume - by MrFixr55 - 11-13-2024, 07:00 PM

RE: Philco 38-2 Low Volume - by dconant - 11-13-2024, 07:28 PM

RE: Philco 38-2 Low Volume - by morzh - 11-13-2024, 08:25 PM

RE: Philco 38-2 Low Volume - by dconant - 11-14-2024, 08:21 AM

RE: Philco 38-2 Low Volume - by dconant - 11-14-2024, 03:57 PM

RE: Philco 38-2 Low Volume - by morzh - 11-14-2024, 04:06 PM

RE: Philco 38-2 Low Volume - by dconant - 11-14-2024, 04:28 PM

RE: Philco 38-2 Low Volume - by dconant - 11-14-2024, 07:35 PM

RE: Philco 38-2 Low Volume - by morzh - 11-14-2024, 07:39 PM

RE: Philco 38-2 Low Volume - by dconant - 11-15-2024, 09:57 AM

RE: Philco 38-2 Low Volume - by morzh - 11-15-2024, 10:02 AM

RE: Philco 38-2 Low Volume - by RodB - 11-15-2024, 11:09 AM

RE: Philco 38-2 Low Volume - by dconant - 11-15-2024, 11:47 AM

RE: Philco 38-2 Low Volume - by RodB - 11-15-2024, 11:55 AM

RE: Philco 38-2 Low Volume - by dconant - 11-15-2024, 12:44 PM

RE: Philco 38-2 Low Volume - by dconant - 11-15-2024, 12:50 PM

RE: Philco 38-2 Low Volume - by morzh - 11-15-2024, 01:42 PM

RE: Philco 38-2 Low Volume - by RodB - 11-15-2024, 03:24 PM

RE: Philco 38-2 Low Volume - by morzh - 11-15-2024, 04:19 PM

RE: Philco 38-2 Low Volume - by dconant - 11-15-2024, 05:36 PM

RE: Philco 38-2 Low Volume - by MrFixr55 - 11-15-2024, 07:31 PM

RE: Philco 38-2 Low Volume - by RodB - 11-15-2024, 08:06 PM

RE: Philco 38-2 Low Volume - by dconant - 11-16-2024, 08:36 AM

RE: Philco 38-2 Low Volume - by radiorich - 11-16-2024, 12:12 PM

RE: Philco 38-2 Low Volume - by dconant - 11-17-2024, 10:55 AM

RE: Philco 38-2 Low Volume - by dconant - Yesterday, 11:03 AM

View a Printable Version

Users browsing this thread: 18 Guest(s)

Recent Posts
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
12' Philco
Not anymore Mike. Andre The Giant Born: May 19, 1946, Coulommiers, France Died: Jan 28, 1993 (46 years), Paris, Fran...RodB — 11:53 PM
IF can wire size and Rubber mounts?
Renovated Radios do carry what you need. As for the voltage, a wire should be at least 300V-rated.morzh — 11:13 PM
12' Philco
Andre the Giant got 2" on Kareem :lol:morzh — 11:11 PM
IF can wire size and Rubber mounts?
Thanks for the info but I doubt that a hardware store would be carrying the proper tuner assembly support mountings for ...georgetownjohn — 10:38 PM
12' Philco
Perhaps Kareem Abdul Jabbar?GarySP — 10:33 PM
My last cabinet for this year
Outstanding work, Dan! Take care and BE HEALTHY! GaryGarySP — 10:31 PM
My last cabinet for this year
They are a nice looking radio, Stromberg. I have a small tabletop octagon-dial one. It sounds surprisingly nice. And t...morzh — 09:40 PM
Philco 41-608 changer coupler
Different years but the same idea.morzh — 09:38 PM
My last cabinet for this year
That’s a beauty! :thumbup:klondike98 — 09:24 PM

Who's Online

There are currently 6536 online users. [Complete List]
» 1 Member(s) | 6535 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me