Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 38-2 Low Volume
#51

MrFixr55 I am using the second schematic, the one with the X parts as that is my radio. The 39A and B are 16X, containing 110pf caps that are in a bakelite block. I had already changed them with silver micas. Having to use two different schematics sure makes this harder. Some sections are on one and some the other.

The coils in both IFs are all good. I had checked them a while ago.

No caps in series with probes. I will try again with caps. I was told a while ago there were blocking caps in the tracer. Not sure about the ground though.

I don't know how to measure the difference frequency. I don't have a scope so the best I might do is a frequency counter but I would not know how to do that either.

As for the non peaking compensator I'm wondering if the internal cap might be bad. The schematic does not list the value for them except for 2XD (110pf) which I changed.

If RF alignment is off could that render the AVC inactive? I'm wondering if I should put the radio aside until I get my dial and then I can do the RF alignment.


Messages In This Thread
Philco 38-2 Low Volume - by dconant - 11-09-2024, 02:27 PM
RE: Philco 38-2 Low Volume - by morzh - 11-09-2024, 03:15 PM
RE: Philco 38-2 Low Volume - by MrFixr55 - 11-09-2024, 10:27 PM
RE: Philco 38-2 Low Volume - by RodB - 11-10-2024, 11:44 AM
RE: Philco 38-2 Low Volume - by dconant - 11-10-2024, 01:23 PM
RE: Philco 38-2 Low Volume - by dconant - 11-10-2024, 02:39 PM
RE: Philco 38-2 Low Volume - by morzh - 11-10-2024, 03:25 PM
RE: Philco 38-2 Low Volume - by MrFixr55 - 11-10-2024, 06:31 PM
RE: Philco 38-2 Low Volume - by RodB - 11-10-2024, 06:52 PM
RE: Philco 38-2 Low Volume - by morzh - 11-10-2024, 07:16 PM
RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 12:05 PM
RE: Philco 38-2 Low Volume - by RodB - 11-11-2024, 01:17 PM
RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 02:06 PM
RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 02:14 PM
RE: Philco 38-2 Low Volume - by RodB - 11-11-2024, 02:36 PM
RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 03:50 PM
RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 04:58 PM
RE: Philco 38-2 Low Volume - by RodB - 11-11-2024, 05:20 PM
RE: Philco 38-2 Low Volume - by RodB - 11-11-2024, 05:38 PM
RE: Philco 38-2 Low Volume - by dconant - 11-11-2024, 06:23 PM
RE: Philco 38-2 Low Volume - by RodB - 11-11-2024, 11:15 PM
RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 08:51 AM
RE: Philco 38-2 Low Volume - by RodB - 11-12-2024, 10:53 AM
RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 11:02 AM
RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 11:16 AM
RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 11:22 AM
RE: Philco 38-2 Low Volume - by RodB - 11-12-2024, 11:43 AM
RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 11:52 AM
RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 11:57 AM
RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 12:02 PM
RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 12:08 PM
RE: Philco 38-2 Low Volume - by MrFixr55 - 11-12-2024, 12:27 PM
RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 12:42 PM
RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 02:07 PM
RE: Philco 38-2 Low Volume - by morzh - 11-12-2024, 02:25 PM
RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 02:57 PM
RE: Philco 38-2 Low Volume - by MrFixr55 - 11-12-2024, 02:57 PM
RE: Philco 38-2 Low Volume - by MrFixr55 - 11-12-2024, 04:24 PM
RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 04:50 PM
RE: Philco 38-2 Low Volume - by MrFixr55 - 11-12-2024, 05:21 PM
RE: Philco 38-2 Low Volume - by dconant - 11-12-2024, 06:04 PM
RE: Philco 38-2 Low Volume - by dconant - 5 hours ago



Users browsing this thread: 7 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Hello Tim, It looks very nice so far ! Sincerely Richardradiorich — 10:55 PM
HiFi (Chifi) tube amp build - but my own design.
It's getting along!morzh — 10:54 PM
HiFi (Chifi) tube amp build - but my own design.
Construction has started! So far, I've gotten the power supply done and filament wiring run. The major layout is finishe...TV MAN — 10:42 PM
RCA WV-98c
Just occurred to me: what if you have a power transformer leak? From a, say, secondary to the case. If it is bolted to t...morzh — 10:24 PM
[split] Newbie questions RE: Philco 41-608
Honestly, I do not see any capacitors, but as long as you know now, what the wiper is, this is all that matters.morzh — 10:17 PM
[split] Newbie questions RE: Philco 41-608
Morzh I changed the capacitor at the volume control as part of the full recap.  Just to confirm the 3rd pin "wip...tmurphy — 09:47 PM
Model 96 cabinet veneer
I thought it looks most like the quarter sawn flexible veneer that Constantine's sells, but I wanted another opinion.  T...TGLager — 09:19 PM
[split] Newbie questions RE: Philco 41-608
MrFixr55 The cap to the left is 21B.  I have the negative tied to the ground with two terminal points.  (See first pic ...tmurphy — 08:59 PM
Philco 39-116 radio and remote
With regard to the 39-116, (at least the U.S versions) I believe that they used rubber/gutta percha wire for the leads, ...Arran — 08:37 PM
Testing a power transformer
Well, this is where you might use that dim bulb. And, as for "can't afford", A $50 one? If you cannot...morzh — 08:28 PM

[-]
Who's Online
There are currently no members online.

>