1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
My first Philco radio.
Oldie Goldie
Junior Member
**
Posts: 6
Threads: 1
Joined: Dec 2024
City: Belleville State, Province, Country: Ontario
#9

Yesterday, 06:31 PM
I looked at the two early and later versions of the "schematic" freely available on the internet.
It's confusing me, I'm used to clean and clear Sams.
The best quality stuff available for the 610 I could find are like bad xerox copies.
I have 1949 Buick Delco sonomatic data sheets that are very clear. But there is no service data on the tuning mechanism for my Philco as I could find.
Find
« Next Oldest | Next Newest »


Messages In This Thread
My first Philco radio. - by Oldie Goldie - Yesterday, 08:10 AM
RE: My first Philco radio. - by jrblasde - Yesterday, 10:59 AM
RE: My first Philco radio. - by klondike98 - Yesterday, 03:27 PM
RE: My first Philco radio. - by Oldie Goldie - Yesterday, 03:51 PM
RE: My first Philco radio. - by morzh - Yesterday, 05:14 PM
RE: My first Philco radio. - by Oldie Goldie - Yesterday, 06:12 PM
RE: My first Philco radio. - by Oldie Goldie - Yesterday, 06:21 PM
RE: My first Philco radio. - by Oldie Goldie - Yesterday, 06:22 PM
RE: My first Philco radio. - by Oldie Goldie - Yesterday, 06:31 PM
RE: My first Philco radio. - by morzh - Yesterday, 08:19 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Custom Hammond Power Transformer
Naval jelly is a rust-removing gel containing phosphoric acid. I do not recommend using it on anything that cannot susta...DaleHCook — 08:18 AM
Custom Hammond Power Transformer
Thank you all for the advice. I’ll remove it from the chassis and get it cleaned up with a wire wheel. I can take it out...jrblasde — 01:21 AM
Custom Hammond Power Transformer
I would take the transformer out and wire wheel it FAR AWAY from the rest of the chassis. Don't need conductive Iron Ox...GarySP — 11:01 PM
Custom Hammond Power Transformer
Is it safe to remove rust on the transformer? It's perfectly safe to use whatever method you like on the bells/covers. I...Arran — 09:34 PM
My first Philco radio.
This is the link to the schematic in our library that jrblasde was pointing you toward. Its a pdf file you can downloa...klondike98 — 08:53 PM
My first Philco radio.
Still no photos. Make sure your photo file is not superlarge. Not sure, but under 1.5MB is OK. If too large, open wit...morzh — 08:19 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Try McMaster-Carr supply they have lots of stuff O rings and flat sheets and solid round tubing. If you had the plans fo...David — 07:54 PM
My first Philco radio.
I looked at the two early and later versions of the "schematic" freely available on the internet. It's confus...Oldie Goldie — 06:31 PM
My first Philco radio.
I'm having a fun-tastic time uploading photos of what I'm seeing. Stand by. The center knob, when I turned it it felt...Oldie Goldie — 06:22 PM
My first Philco radio.
I'm having a fun-tastic time uploading photos of what I'm seeing. Stand by. The center knob, when I turned it it felt...Oldie Goldie — 06:21 PM

[-]
Who's Online
There are currently 313 online users. [Complete List]
» 2 Member(s) | 311 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios