1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
My first Philco radio.
Radioroslyn
Phorum Expert
*****
Posts: 7,295
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#24

5 hours ago
Maybe it's time to replace the 3 ball bearings. I've done it on a few sets to lessen the roughness in the tuning.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
My first Philco radio. - by Oldie Goldie - 12-21-2024, 08:10 AM
RE: My first Philco radio. - by jrblasde - 12-21-2024, 10:59 AM
RE: My first Philco radio. - by klondike98 - 12-21-2024, 03:27 PM
RE: My first Philco radio. - by morzh - 12-21-2024, 05:14 PM
RE: My first Philco radio. - by Oldie Goldie - 12-21-2024, 06:12 PM
RE: My first Philco radio. - by Oldie Goldie - 12-21-2024, 06:21 PM
RE: My first Philco radio. - by Oldie Goldie - 12-21-2024, 06:31 PM
RE: My first Philco radio. - by morzh - 12-21-2024, 08:19 PM
RE: My first Philco radio. - by klondike98 - 12-21-2024, 08:53 PM
RE: My first Philco radio. - by RodB - Yesterday, 11:43 AM
RE: My first Philco radio. - by morzh - Yesterday, 11:46 AM
RE: My first Philco radio. - by RodB - Yesterday, 12:06 PM
RE: My first Philco radio. - by Oldie Goldie - Yesterday, 02:39 PM
RE: My first Philco radio. - by Oldie Goldie - Yesterday, 02:45 PM
RE: My first Philco radio. - by Oldie Goldie - Yesterday, 02:55 PM
RE: My first Philco radio. - by Oldie Goldie - Yesterday, 03:04 PM
RE: My first Philco radio. - by Oldie Goldie - Yesterday, 03:07 PM
RE: My first Philco radio. - by Oldie Goldie - Yesterday, 03:18 PM
RE: My first Philco radio. - by Radioroslyn - 5 hours ago



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My first Philco radio.
morzh, the center shaft has one ball bearing than a spring than another ball bearing. The outer tube has three bigger ba...Oldie Goldie — 01:29 AM
My first Philco radio.
This assembly usually have 3 larger bolls, from the sides, and one smaller, at the bottom, under the shaft.morzh — 11:41 PM
250 ohm micamold resistor
It's less than ten percent over. It's OK.RodB — 11:07 PM
Custom Hammond Power Transformer
Boy howdy, that’s some nice custom testing equipment! I really do need to invest in a variac. I also have a tube tester ...jrblasde — 10:46 PM
250 ohm micamold resistor
Thought I'd ask the experts. This is a Philco 38-12CI.  The 250 ohm resistor comes out to 261 ohms. I'm not sure what th...DJW — 10:35 PM
My first Philco radio.
Maybe it's time to replace the 3 ball bearings. I've done it on a few sets to lessen the roughness in the tuning.Radioroslyn — 10:04 PM
My first Philco radio.
I have a theory. One of the three big balls bearings came out while the other two wouldn't slide out. I didn't think it...Oldie Goldie — 09:21 PM
My first Philco radio.
I don't get this. Is the spring too strong or gotten weak and that's why the ball bearings are losing the grasp on the i...Oldie Goldie — 08:58 PM
My first Philco radio.
I put it all to bed for the night. In the morning I'm going to try to get the three big balls bearings out and see what'...Oldie Goldie — 08:46 PM
My first Philco radio.
I had no idea the heart of the tuning mechanism was based on such an unnecessarily complicated fragile design. With such...Oldie Goldie — 08:31 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios