1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Custom Hammond Power Transformer
DaleHCook
Philco, Zenith, and Howard Phan
***
Posts: 168
Threads: 8
Joined: Apr 2023
City: Roanoke State, Province, Country: Virginia
#33

4 hours ago
jrblasde Wrote:  I currently have no way of testing tubes other than eliminating all other problems first.

Bear in mind that no tube tester can tell you if a tube is good - it can only tell you if it is likely or definitely bad.
Dale H. Cook, GR/HP/Tek Collector, Roanoke/Lynchburg, VA
https://plymouthcolony.net/starcity/radios/
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Custom Hammond Power Transformer - by jrblasde - 12-20-2024, 11:12 AM
RE: Custom Hammond Power Transformer - by morzh - 12-20-2024, 11:34 AM
RE: Custom Hammond Power Transformer - by morzh - 12-20-2024, 11:57 AM
RE: Custom Hammond Power Transformer - by GarySP - 12-20-2024, 12:53 PM
RE: Custom Hammond Power Transformer - by morzh - 12-20-2024, 01:45 PM
RE: Custom Hammond Power Transformer - by TV MAN - 12-20-2024, 02:44 PM
RE: Custom Hammond Power Transformer - by morzh - 12-20-2024, 02:46 PM
RE: Custom Hammond Power Transformer - by Arran - 12-20-2024, 03:36 PM
RE: Custom Hammond Power Transformer - by morzh - 12-20-2024, 05:43 PM
RE: Custom Hammond Power Transformer - by TV MAN - 12-20-2024, 06:21 PM
RE: Custom Hammond Power Transformer - by Arran - 12-20-2024, 08:43 PM
RE: Custom Hammond Power Transformer - by TV MAN - 12-20-2024, 09:10 PM
RE: Custom Hammond Power Transformer - by GarySP - 12-20-2024, 09:12 PM
RE: Custom Hammond Power Transformer - by morzh - 12-20-2024, 10:35 PM
RE: Custom Hammond Power Transformer - by Arran - 12-20-2024, 10:49 PM
RE: Custom Hammond Power Transformer - by Arran - 12-21-2024, 09:34 PM
RE: Custom Hammond Power Transformer - by GarySP - 12-21-2024, 11:01 PM
RE: Custom Hammond Power Transformer - by DaleHCook - 4 hours ago



Users browsing this thread: Steve Davis, 1 Guest(s)
[-]
Recent Posts
My first Philco radio.
Okay gents I went at this with a fresh eye this morning. Cleaned everything all over again. There is wear and slop som...Oldie Goldie — 11:31 AM
Custom Hammond Power Transformer
I currently have no way of testing tubes other than eliminating all other problems first. Bear in mind that no tube t...DaleHCook — 07:31 AM
My first Philco radio.
morzh, the center shaft has one ball bearing than a spring than another ball bearing. The outer tube has three bigger ba...Oldie Goldie — 01:29 AM
My first Philco radio.
This assembly usually have 3 larger bolls, from the sides, and one smaller, at the bottom, under the shaft.morzh — 11:41 PM
250 ohm micamold resistor
It's less than ten percent over. It's OK.RodB — 11:07 PM
Custom Hammond Power Transformer
Boy howdy, that’s some nice custom testing equipment! I really do need to invest in a variac. I also have a tube tester ...jrblasde — 10:46 PM
250 ohm micamold resistor
Thought I'd ask the experts. This is a Philco 38-12CI.  The 250 ohm resistor comes out to 261 ohms. I'm not sure what th...DJW — 10:35 PM
My first Philco radio.
Maybe it's time to replace the 3 ball bearings. I've done it on a few sets to lessen the roughness in the tuning.Radioroslyn — 10:04 PM
My first Philco radio.
I have a theory. One of the three big balls bearings came out while the other two wouldn't slide out. I didn't think it...Oldie Goldie — 09:21 PM
My first Philco radio.
I don't get this. Is the spring too strong or gotten weak and that's why the ball bearings are losing the grasp on the i...Oldie Goldie — 08:58 PM

[-]
Who's Online
There are currently 1967 online users. [Complete List]
» 4 Member(s) | 1963 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration