1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco IF Coil
Chas
Senior Member
****
Posts: 713
Threads: 8
Joined: Apr 2018
City: S. Dartmouth State, Province, Country: MA
#5

01-06-2025, 10:09 PM
Quote:Weller 325 watt gun.
Try an iron not much more than 100 watts with a large copper tip so heat is stored in the tip. If still reluctant, try using SMD low temperature rework solder. The low temp alloys will amalgamate with the higher temp alloy and lower the temperature of the original and melt the joint.

Chas
Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco IF Coil - by dconant - 01-06-2025, 09:39 AM
RE: Philco IF Coil - by morzh - 01-06-2025, 10:01 AM
RE: Philco IF Coil - by dconant - 01-06-2025, 10:49 AM
RE: Philco IF Coil - by morzh - 01-06-2025, 11:29 AM
RE: Philco IF Coil - by Chas - 01-06-2025, 10:09 PM



Users browsing this thread:
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM

[-]
Who's Online
There are currently 1663 online users. [Complete List]
» 1 Member(s) | 1662 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration