Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New 37-116 Parts
#14

Hi Greg,

No I am not requesting a new one but maybe I should have since others will be buying it and may not like it. They did say they would be will to try again. I decided it is not quite so noticeable behind the glass with the pilot light(s) on although you can still see it close up. I would like to know if you decide to get one and if you do what you think of it.

Dan


Messages In This Thread
New 37-116 Parts - by Doppleganger - 03-04-2025, 02:08 AM
RE: New 37-116 Parts - by morzh - 03-04-2025, 10:33 AM
RE: New 37-116 Parts - by Doppleganger - 03-04-2025, 12:34 PM
RE: New 37-116 Parts - by morzh - 03-04-2025, 02:30 PM
RE: New 37-116 Parts - by GarySP - 03-04-2025, 04:02 PM
RE: New 37-116 Parts - by morzh - 03-04-2025, 04:05 PM
RE: New 37-116 Parts - by dconant - 03-04-2025, 04:34 PM
RE: New 37-116 Parts - by Arran - 03-04-2025, 05:29 PM
RE: New 37-116 Parts - by Doppleganger - 03-04-2025, 09:11 PM
RE: New 37-116 Parts - by dconant - 03-05-2025, 04:35 PM
RE: New 37-116 Parts - by Doppleganger - 03-14-2025, 01:09 PM
RE: New 37-116 Parts - by dconant - 03-14-2025, 01:22 PM
RE: New 37-116 Parts - by Greg - 03-14-2025, 01:59 PM
RE: New 37-116 Parts - by dconant - Yesterday, 08:21 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
[split] New member...
Are you sure that the flange at the end of the shaft isn't just completely worn off or bent over causing the indentation...rfeenstra — 11:03 PM
Model 84 late buzz( 1935 run)
Hi Bruce, I am looking at the pic. Seems that the 2 filter caps are sharing a common negative. That common negativ...MrFixr55 — 10:55 PM
[split] New member...
I think you’re right about everything. A couple years later they were machining it out of a single piece of metal. Still...HowardWoodard — 10:49 PM
[split] New member...
Looking at the drawing, the ball should be glued well, as it seems that it rolling against the 3 other balls is what pro...morzh — 10:29 PM
[split] New member...
It is concave and the balls rests in it about 25%-33% of the circumference of the ball.  I'm just contemplating which wo...HowardWoodard — 09:03 PM
38-690 Gill Cloth
Thinking of it, the cloth on both 37-690 and 38-690 is flat, no pattern, not embossed, pinkish-yellowish type. If you h...morzh — 08:44 PM
38-690 Gill Cloth
thank youtargeteye — 08:38 PM
[split] New member...
I think that's the one I have in Philco 60, which I have recently fixed. The last robodial radio repair (38-690) happen...morzh — 04:58 PM
[split] New member...
Hi Ron. Yes, I got it all back together the first time, after getting it all cleaned and lubed, and it was working real...HowardWoodard — 03:34 PM
[split] New member...
Wow morzh, you have access to some very useful doc.  That cross-section (Fig 2) is dynamite. As you can see, if t...HowardWoodard — 03:30 PM

[-]
Who's Online
There are currently 1856 online users. [Complete List]
» 2 Member(s) | 1854 Guest(s)
AvatarAvatar

>