1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
[split] New member...
HowardWoodard
Junior Member
**
Posts: 16
Threads: 1
Joined: Mar 2025
City: Puyallup State, Province, Country: WA
#26

8 hours ago
Hi morzh.  I apologize for being so dense, but I clearly must not be understanding what you are saying because when I try what I think you are saying, the fine-tuning shaft will not stay in.  In the included picture I'm showing you what I think you said I should do.  Please let me know where I'm misinterpreting you.

   
Find
« Next Oldest | Next Newest »


Messages In This Thread
[split] New member... - by radiorich - 03-13-2025, 01:16 AM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:24 PM
RE: [split] New member... - by GarySP - 03-13-2025, 05:27 PM
RE: [split] New member... - by morzh - 03-13-2025, 05:34 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:48 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:58 PM
RE: [split] New member... - by morzh - 03-13-2025, 06:47 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 06:56 PM
RE: [split] New member... - by morzh - 03-13-2025, 07:17 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 08:10 PM
462ron - by 462ron - 03-14-2025, 09:00 AM
RE: [split] New member... - by HowardWoodard - 03-14-2025, 11:39 AM
RE: [split] New member... - by morzh - 03-14-2025, 04:31 PM
RE: [split] New member... - by HowardWoodard - Yesterday, 12:24 AM
RE: [split] New member... - by morzh - Yesterday, 10:29 AM
RE: [split] New member... - by MrFixr55 - Yesterday, 12:57 PM
RE: [split] New member... - by morzh - 10 hours ago
RE: [split] New member... - by HowardWoodard - 8 hours ago
RE: [split] New member... - by morzh - 7 hours ago
RE: [split] New member... - by morzh - 7 hours ago
RE: [split] New member... - by morzh - 6 hours ago
RE: New member... - by MrFixr55 - 03-13-2025, 10:14 AM
RE: New member... - by HowardWoodard - 03-13-2025, 12:48 PM
RE: New member... - by GarySP - 03-13-2025, 02:20 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 41 280 Floor radio-new project.
Rough but restorable. The rubber wiring seems to be in OK shape; the white wires often stay pliable and do not need to ...morzh — 11:03 PM
Philco 41 280 Floor radio-new project.
Hello willits18, First of all I wanted to say welcome to our little forum. over all that set does not look in to bad o...radiorich — 10:48 PM
Philco 41 280 Floor radio-new project.
Just picked this up locally. No power cord. When I tested the tubes I think I know why. 3 bad tubes, 2 shorted, and 1 ba...willits18 — 10:08 PM
Model 41-280 5 dials
for the dial you can try Radio Daze.  willits18 — 09:58 PM
Model 41-280 5 dials
For the dial you can try Radio Daze willits18 — 09:57 PM
[split] New member...
See if this helps. This is Philco Auto Tuning service bulletin. I think this is same as yours. I used it on my 37-...morzh — 08:14 PM
[split] New member...
In my shafts (yes they are a bit differnt but the idea is the same, three balls as planetary gear and a small ball and a...morzh — 08:00 PM
42-345 Resistors
Thank you to everyone who has replied. The two mystery objects are either mini cannoli or oscillators. I'm not quite su...proftrussell — 07:57 PM
[split] New member...
Btw, the thread you provided me with the service hint & tip on refurbishing this tuning shaft was written by "...HowardWoodard — 07:55 PM
[split] New member...
Yes the three ball bearings should go in the holes. The spring with teh cap should go first, then the balls (with some l...morzh — 07:21 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration