Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

[split] New member...
#28

Btw, the thread you provided me (https://philcoradio.com/repairbench/tips/svctip39.htm) with the service hint & tip on refurbishing this tuning shaft was written by "Tom Burke" in 2004.  I don't find a Tom Burke listed as a user her on this site.  Perhaps he was an employee of Westridge Consulting who copyrighted the article.

He's the guy who used his own lath to refinish what he called the "end-ball".  It would be nice to be able to ask him if that ball came apart from the shaft.  It reads like it did not.


Messages In This Thread
[split] New member... - by radiorich - 03-13-2025, 01:16 AM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:24 PM
RE: [split] New member... - by GarySP - 03-13-2025, 05:27 PM
RE: [split] New member... - by morzh - 03-13-2025, 05:34 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:48 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:58 PM
RE: [split] New member... - by morzh - 03-13-2025, 06:47 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 06:56 PM
RE: [split] New member... - by morzh - 03-13-2025, 07:17 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 08:10 PM
462ron - by 462ron - 03-14-2025, 09:00 AM
RE: [split] New member... - by HowardWoodard - 03-14-2025, 11:39 AM
RE: [split] New member... - by morzh - 03-14-2025, 04:31 PM
RE: [split] New member... - by HowardWoodard - 03-15-2025, 12:24 AM
RE: [split] New member... - by morzh - 03-15-2025, 10:29 AM
RE: [split] New member... - by MrFixr55 - 03-15-2025, 12:57 PM
RE: [split] New member... - by HowardWoodard - 03-15-2025, 03:50 PM
RE: [split] New member... - by morzh - 03-15-2025, 04:32 PM
RE: [split] New member... - by HowardWoodard - 03-15-2025, 06:50 PM
RE: [split] New member... - by morzh - 03-15-2025, 07:21 PM
RE: [split] New member... - by HowardWoodard - 03-15-2025, 07:55 PM
RE: [split] New member... - by morzh - 03-15-2025, 08:00 PM
RE: [split] New member... - by morzh - 03-15-2025, 08:14 PM
462ron - by 462ron - Yesterday, 07:37 AM
RE: [split] New member... - by morzh - Yesterday, 09:09 AM
RE: [split] New member... - by HowardWoodard - Yesterday, 03:30 PM
RE: [split] New member... - by HowardWoodard - Yesterday, 03:34 PM
RE: [split] New member... - by morzh - 11 hours ago
RE: [split] New member... - by morzh - 5 hours ago
RE: New member... - by MrFixr55 - 03-13-2025, 10:14 AM
RE: New member... - by HowardWoodard - 03-13-2025, 12:48 PM
RE: New member... - by GarySP - 03-13-2025, 02:20 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
[split] New member...
As you might have already surmised, I’m not sure of anything. You raise a good question and your pic gives it credibilit...HowardWoodard — 02:08 AM
[split] New member...
Are you sure that the flange at the end of the shaft isn't just completely worn off or bent over causing the indentation...rfeenstra — 11:03 PM
Model 84 late buzz( 1935 run)
Hi Bruce, I am looking at the pic. Seems that the 2 filter caps are sharing a common negative. That common negativ...MrFixr55 — 10:55 PM
[split] New member...
I think you’re right about everything. A couple years later they were machining it out of a single piece of metal. Still...HowardWoodard — 10:49 PM
[split] New member...
Looking at the drawing, the ball should be glued well, as it seems that it rolling against the 3 other balls is what pro...morzh — 10:29 PM
[split] New member...
It is concave and the balls rests in it about 25%-33% of the circumference of the ball.  I'm just contemplating which wo...HowardWoodard — 09:03 PM
38-690 Gill Cloth
Thinking of it, the cloth on both 37-690 and 38-690 is flat, no pattern, not embossed, pinkish-yellowish type. If you h...morzh — 08:44 PM
38-690 Gill Cloth
thank youtargeteye — 08:38 PM
[split] New member...
I think that's the one I have in Philco 60, which I have recently fixed. The last robodial radio repair (38-690) happen...morzh — 04:58 PM
[split] New member...
Hi Ron. Yes, I got it all back together the first time, after getting it all cleaned and lubed, and it was working real...HowardWoodard — 03:34 PM

[-]
Who's Online
There are currently no members online.

>