1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
[split] New member...
morzh
Odobenus rosmarus
******
Posts: 16,406
Threads: 572
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#29

7 hours ago
In my shafts (yes they are a bit differnt but the idea is the same, three balls as planetary gear and a small ball and a spring at the end) that small ball was separate. Even if it was glued (doubt it), it would be just to hold it to make the insertion easy. No functional change because of it.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »


Messages In This Thread
[split] New member... - by radiorich - 03-13-2025, 01:16 AM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:24 PM
RE: [split] New member... - by GarySP - 03-13-2025, 05:27 PM
RE: [split] New member... - by morzh - 03-13-2025, 05:34 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:48 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:58 PM
RE: [split] New member... - by morzh - 03-13-2025, 06:47 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 06:56 PM
RE: [split] New member... - by morzh - 03-13-2025, 07:17 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 08:10 PM
462ron - by 462ron - 03-14-2025, 09:00 AM
RE: [split] New member... - by HowardWoodard - 03-14-2025, 11:39 AM
RE: [split] New member... - by morzh - 03-14-2025, 04:31 PM
RE: [split] New member... - by HowardWoodard - Yesterday, 12:24 AM
RE: [split] New member... - by morzh - Yesterday, 10:29 AM
RE: [split] New member... - by MrFixr55 - Yesterday, 12:57 PM
RE: [split] New member... - by morzh - 10 hours ago
RE: [split] New member... - by morzh - 7 hours ago
RE: [split] New member... - by morzh - 7 hours ago
RE: [split] New member... - by morzh - 6 hours ago
RE: New member... - by MrFixr55 - 03-13-2025, 10:14 AM
RE: New member... - by HowardWoodard - 03-13-2025, 12:48 PM
RE: New member... - by GarySP - 03-13-2025, 02:20 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41 280 Floor radio-new project.
Rough but restorable. The rubber wiring seems to be in OK shape; the white wires often stay pliable and do not need to ...morzh — 11:03 PM
Philco 41 280 Floor radio-new project.
Hello willits18, First of all I wanted to say welcome to our little forum. over all that set does not look in to bad o...radiorich — 10:48 PM
Philco 41 280 Floor radio-new project.
Just picked this up locally. No power cord. When I tested the tubes I think I know why. 3 bad tubes, 2 shorted, and 1 ba...willits18 — 10:08 PM
Model 41-280 5 dials
for the dial you can try Radio Daze.  willits18 — 09:58 PM
Model 41-280 5 dials
For the dial you can try Radio Daze willits18 — 09:57 PM
[split] New member...
See if this helps. This is Philco Auto Tuning service bulletin. I think this is same as yours. I used it on my 37-...morzh — 08:14 PM
[split] New member...
In my shafts (yes they are a bit differnt but the idea is the same, three balls as planetary gear and a small ball and a...morzh — 08:00 PM
42-345 Resistors
Thank you to everyone who has replied. The two mystery objects are either mini cannoli or oscillators. I'm not quite su...proftrussell — 07:57 PM
[split] New member...
Btw, the thread you provided me with the service hint & tip on refurbishing this tuning shaft was written by "...HowardWoodard — 07:55 PM
[split] New member...
Yes the three ball bearings should go in the holes. The spring with teh cap should go first, then the balls (with some l...morzh — 07:21 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration