1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
[split] New member...
morzh
Odobenus rosmarus
******
Posts: 16,418
Threads: 571
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#47

5 hours ago
If I were too design that (I mean I woulbe told to use ball gear or be fired), I would machine a ball with a small pin at the end, drill a hole in the shaft (concave) and glued the pin in the hole. That would be unbreakable. Better yet, just drill two holes, in the shaft and in the ball, and use separate pin.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »


Messages In This Thread
[split] New member... - by radiorich - 03-13-2025, 01:16 AM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:24 PM
RE: [split] New member... - by GarySP - 03-13-2025, 05:27 PM
RE: [split] New member... - by morzh - 03-13-2025, 05:34 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:48 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 05:58 PM
RE: [split] New member... - by morzh - 03-13-2025, 06:47 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 06:56 PM
RE: [split] New member... - by morzh - 03-13-2025, 07:17 PM
RE: [split] New member... - by HowardWoodard - 03-13-2025, 08:10 PM
462ron - by 462ron - 03-14-2025, 09:00 AM
RE: [split] New member... - by HowardWoodard - 03-14-2025, 11:39 AM
RE: [split] New member... - by morzh - 03-14-2025, 04:31 PM
RE: [split] New member... - by HowardWoodard - 03-15-2025, 12:24 AM
RE: [split] New member... - by morzh - 03-15-2025, 10:29 AM
RE: [split] New member... - by MrFixr55 - 03-15-2025, 12:57 PM
RE: [split] New member... - by HowardWoodard - 03-15-2025, 03:50 PM
RE: [split] New member... - by morzh - 03-15-2025, 04:32 PM
RE: [split] New member... - by HowardWoodard - 03-15-2025, 06:50 PM
RE: [split] New member... - by morzh - 03-15-2025, 07:21 PM
RE: [split] New member... - by HowardWoodard - 03-15-2025, 07:55 PM
RE: [split] New member... - by morzh - 03-15-2025, 08:00 PM
RE: [split] New member... - by morzh - 03-15-2025, 08:14 PM
462ron - by 462ron - 03-16-2025, 07:37 AM
RE: [split] New member... - by morzh - 03-16-2025, 09:09 AM
RE: [split] New member... - by HowardWoodard - 03-16-2025, 03:30 PM
RE: [split] New member... - by HowardWoodard - 03-16-2025, 03:34 PM
RE: [split] New member... - by morzh - 03-16-2025, 04:58 PM
RE: [split] New member... - by HowardWoodard - 03-16-2025, 09:03 PM
RE: [split] New member... - by morzh - 03-16-2025, 10:29 PM
RE: [split] New member... - by HowardWoodard - 03-16-2025, 10:49 PM
RE: [split] New member... - by rfeenstra - 03-16-2025, 11:03 PM
RE: [split] New member... - by HowardWoodard - 03-17-2025, 02:08 AM
RE: [split] New member... - by morzh - 5 hours ago
RE: [split] New member... - by RodB - 4 hours ago
RE: New member... - by MrFixr55 - 03-13-2025, 10:14 AM
RE: New member... - by HowardWoodard - 03-13-2025, 12:48 PM
RE: New member... - by GarySP - 03-13-2025, 02:20 PM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco model #20
The resistor is just a hank of wire, if not burned, you can't do any better, just reinstall it. If the .05 capacitor (al...Steve Davis — 12:17 AM
Philco model #20
This is a better quality sch for the late 20 model.morzh — 11:05 PM
Philco model #20
You can use 1/4W resistor and hide it inside.morzh — 11:01 PM
Philco model #20
Hello again fellows, just wanted to ask another question on number 8 Bakelite condenser block it has a .05 Uf cap and in...onlyrick — 10:22 PM
Zenith H725
Ed: I'm not sure how much work you want to put into this but you could convert the set from being a hot chassis to a ...Arran — 10:08 PM
[split] New member...
This is not the place to buy or sell!  PM me.rfeenstra — 08:30 PM
[split] New member...
The outer housing has a hole in the side where a pin fits loosely (removable with a strong magnet, or in this case strik...rfeenstra — 08:29 PM
[split] New member...
I may end up buying a whole chassis + shipping just to get the shaft -- no pun intended. :) -- because at the end of the...HowardWoodard — 08:20 PM
[split] New member...
Hi Ron.  That pin holds the coarse shaft in place.  If the coarse shaft can't move, then it's three ball bearings preven...HowardWoodard — 08:11 PM
[split] New member...
Rob, any light as to how the whole assy is kept together?RodB — 07:58 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration