Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My Philco 37-116 Restore
#17

Mine was bad too.
I got a replacement off of ebay, a 32-7056N (not sure what the N means).
That's not the "same" part as the original is 32-7491.
However, I believe that if you look in parts catalogs for the specs you'll find they are the same.
The only "difference" is that leads exit differently.
One has both leads on one side and the other has them on opposite sides. (Don't recall which is which).

If you order one, be careful as I suspect it could be bad too.

I see two 32-7056 listed. One seems $$ and the other $$$.

Can't think of anything witty.
Greg O.
Whitehall, PA


Messages In This Thread
My Philco 37-116 Restore - by dconant - 01-16-2025, 12:43 PM
RE: My Philco 37-116 Restore - by rfeenstra - 01-16-2025, 01:20 PM
RE: My Philco 37-116 Restore - by morzh - 01-16-2025, 03:45 PM
RE: My Philco 37-116 Restore - by RodB - 01-16-2025, 04:52 PM
RE: My Philco 37-116 Restore - by rfeenstra - 01-16-2025, 06:24 PM
RE: My Philco 37-116 Restore - by dconant - 01-17-2025, 08:44 AM
462ron - by 462ron - 01-17-2025, 09:02 AM
RE: My Philco 37-116 Restore - by RodB - 01-17-2025, 10:42 AM
RE: My Philco 37-116 Restore - by dconant - 01-17-2025, 01:15 PM
RE: My Philco 37-116 Restore - by morzh - 01-17-2025, 01:55 PM
RE: My Philco 37-116 Restore - by dconant - 01-22-2025, 05:14 PM
RE: My Philco 37-116 Restore - by morzh - 01-22-2025, 09:18 PM
RE: My Philco 37-116 Restore - by dconant - 02-19-2025, 10:47 AM
RE: My Philco 37-116 Restore - by RodB - 02-19-2025, 11:48 AM
RE: My Philco 37-116 Restore - by morzh - 02-19-2025, 01:33 PM
RE: My Philco 37-116 Restore - by dconant - Yesterday, 11:25 AM
RE: My Philco 37-116 Restore - by Greg - Yesterday, 12:19 PM
RE: My Philco 37-116 Restore - by dconant - Yesterday, 12:35 PM
RE: My Philco 37-116 Restore - by Greg - Yesterday, 12:55 PM
RE: My Philco 37-116 Restore - by dconant - Yesterday, 01:00 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
1950 Emerson TV resurrection attempt
Check the power supply for the ATSC / NTSC convertor or other input. Had an experience yesterday with a wireless mic re...MrFixr55 — 12:06 AM
1950 Emerson TV resurrection attempt
Hello Tim, It looks like you are coming right along and one thing is that 75 ohm to 300ohm Balum I have found some that...radiorich — 11:35 PM
[split] New member...
Hi Howard, You could try to degrease the heck out of the shaft and single ball bearing, rough up a small section and u...MrFixr55 — 11:03 PM
1950 Emerson TV resurrection attempt
For what it's worth, I've had the best luck with Zenith DTT901 converter boxes. Bob Andersen — 10:25 PM
Zenith H725
Hey Rich, WARNING! If you think like me, seek help! I have a couple of these Zeniths and one DuMont battery / Line p...MrFixr55 — 09:53 PM
Zenith H725
Had a little fun with the Zenith today.. I'll get pictures up here later. The first thing I tackled was documenting eve...EdHolland — 09:41 PM
Philco 39-7C Restore
Hello Bob, Nice work on that trasformer ! Sincerely Richardradiorich — 09:32 PM
Philco 39-7C Restore
Thanks Mike, I will do that check. Just a bit of progress today but ready to put the shell back on and reinstall the po...klondike98 — 07:36 PM
Philco 39-7C Restore
Bob Transformer may heat up for reasons that are not its own; it could be loaded heavier than appropriate. But if it di...morzh — 04:27 PM
Philco 39-7C Restore
Thanks Mike. It actually seems to be ok, at least it ohms out ok with no shorts. I will try getting the wires reinsula...klondike98 — 03:12 PM

[-]
Who's Online
There are currently no members online.

>