Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My Philco 37-116 Restore
#25

I did not read anything like this im MrFixr's post.
Any AA5 radio would have its B+ under 200V, so 500V electrolytic is just fine there.
Not just that, B+ in transformer sets is more like 300-plus Volts, and before the filter it is closer to 350-370VV and briefly shoots up to 420-450V before the load kicks in, and they used 450V caps originally (I use 500V). And even this is just fine.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
My Philco 37-116 Restore - by dconant - 01-16-2025, 12:43 PM
RE: My Philco 37-116 Restore - by rfeenstra - 01-16-2025, 01:20 PM
RE: My Philco 37-116 Restore - by morzh - 01-16-2025, 03:45 PM
RE: My Philco 37-116 Restore - by RodB - 01-16-2025, 04:52 PM
RE: My Philco 37-116 Restore - by rfeenstra - 01-16-2025, 06:24 PM
RE: My Philco 37-116 Restore - by dconant - 01-17-2025, 08:44 AM
462ron - by 462ron - 01-17-2025, 09:02 AM
RE: My Philco 37-116 Restore - by RodB - 01-17-2025, 10:42 AM
RE: My Philco 37-116 Restore - by dconant - 01-17-2025, 01:15 PM
RE: My Philco 37-116 Restore - by morzh - 01-17-2025, 01:55 PM
RE: My Philco 37-116 Restore - by dconant - 01-22-2025, 05:14 PM
RE: My Philco 37-116 Restore - by morzh - 01-22-2025, 09:18 PM
RE: My Philco 37-116 Restore - by dconant - 02-19-2025, 10:47 AM
RE: My Philco 37-116 Restore - by RodB - 02-19-2025, 11:48 AM
RE: My Philco 37-116 Restore - by morzh - 02-19-2025, 01:33 PM
RE: My Philco 37-116 Restore - by dconant - 03-21-2025, 11:25 AM
RE: My Philco 37-116 Restore - by Greg - 03-21-2025, 12:19 PM
RE: My Philco 37-116 Restore - by dconant - 03-21-2025, 12:35 PM
RE: My Philco 37-116 Restore - by Greg - 03-21-2025, 12:55 PM
RE: My Philco 37-116 Restore - by dconant - 03-21-2025, 01:00 PM
RE: My Philco 37-116 Restore - by dconant - 03-22-2025, 03:13 PM
RE: My Philco 37-116 Restore - by MrFixr55 - 03-22-2025, 10:25 PM
RE: My Philco 37-116 Restore - by morzh - 03-22-2025, 10:50 PM
RE: My Philco 37-116 Restore - by dconant - 03-23-2025, 09:29 AM
RE: My Philco 37-116 Restore - by morzh - 03-23-2025, 09:58 AM
RE: My Philco 37-116 Restore - by dconant - Yesterday, 01:25 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model #20
>> jumper wire going from tab #4 to tab #6 ? If you look at the sch, you will see your answer. Try to get to read...morzh — 06:03 PM
Zenith H725
Well, the plan worked. I unsoldered the wires to the primary of the third 455kHz IF transformer. A small toroid was ...EdHolland — 04:25 PM
Philco model #20
too late I unsoldered the wires going to the can then removed the can form the radio separated it from the phenolic pane...onlyrick — 03:55 PM
Philco model #20
Next time (unless you meat the same) try to do this: Treat it same as a backelite can: - Cut the wires coming out ...morzh — 01:41 PM
40-190 part
Either a resistor or a cap. A closer take with legible marking could help.morzh — 01:37 PM
40-190 part
Hello I am new to posting, I am looking for information on a part in this radio. I am posting a picture of this par...N9BQA — 12:20 PM
Philco model #20
hello Rick, Sounds good I am looking forward to seeing and hearing about your progress . I have a Philco 38-10 that I ...radiorich — 12:15 PM
Philco model #20
Thanks for the help , I will solder the condensers in the cap of the can tonight , what I did was take the rectangle ca...onlyrick — 11:15 AM
Zenith H725
Looking forward to some more work on this today. First off, to isolate the source of noise once and for all. I have a cu...EdHolland — 10:57 AM
Stewart Warner 62T16
Paul, yes the 9003-B is the same chassis in my Firestone. Oddly, the Woolerac 3-3A I have is also a variant of the Stewa...RodB — 10:28 AM

[-]
Who's Online
There are currently 1084 online users. [Complete List]
» 2 Member(s) | 1082 Guest(s)
AvatarAvatar

>