Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco model #20
#25

Next time (unless you meat the same) try to do this:

Treat it same as a backelite can:

- Cut the wires coming out from the inside the can to the solder lugs.
- Then remove the can after unbolting it.
- The phenolic panel therefore is left in the radio with all wires coming to it still soldered to it.
- Clean the lugs (only if you want it).
- Then gut the can.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Philco model #20 - by onlyrick - 03-17-2025, 08:44 PM
RE: Philco model #20 - by morzh - 03-17-2025, 09:15 PM
RE: Philco model #20 - by morzh - 03-17-2025, 09:17 PM
RE: Philco model #20 - by morzh - 03-17-2025, 09:17 PM
RE: Philco model #20 - by MrFixr55 - 03-17-2025, 09:48 PM
RE: Philco model #20 - by onlyrick - 03-17-2025, 10:46 PM
RE: Philco model #20 - by onlyrick - 03-18-2025, 10:22 PM
RE: Philco model #20 - by morzh - 03-18-2025, 11:01 PM
RE: Philco model #20 - by morzh - 03-18-2025, 11:05 PM
RE: Philco model #20 - by Steve Davis - 03-19-2025, 12:17 AM
RE: Philco model #20 - by morzh - 03-19-2025, 12:26 PM
RE: Philco model #20 - by onlyrick - 03-19-2025, 10:27 PM
RE: Philco model #20 - by onlyrick - 03-21-2025, 10:00 AM
RE: Philco model #20 - by onlyrick - 03-23-2025, 05:01 PM
RE: Philco model #20 - by MrFixr55 - 03-23-2025, 08:35 PM
RE: Philco model #20 - by onlyrick - 03-23-2025, 09:53 PM
RE: Philco model #20 - by Steve Davis - 03-24-2025, 02:02 PM
RE: Philco model #20 - by morzh - 03-24-2025, 02:41 PM
RE: Philco model #20 - by onlyrick - 03-24-2025, 03:34 PM
RE: Philco model #20 - by morzh - 03-24-2025, 06:19 PM
RE: Philco model #20 - by onlyrick - 03-26-2025, 09:37 PM
RE: Philco model #20 - by morzh - 03-27-2025, 12:40 AM
RE: Philco model #20 - by onlyrick - 03-27-2025, 11:15 AM
RE: Philco model #20 - by radiorich - 03-27-2025, 12:15 PM
RE: Philco model #20 - by morzh - 03-27-2025, 01:41 PM
RE: Philco model #20 - by onlyrick - 03-27-2025, 03:55 PM
RE: Philco model #20 - by morzh - 03-27-2025, 06:03 PM
RE: Philco model #20 - by onlyrick - 03-27-2025, 09:23 PM
RE: Philco model #20 - by morzh - 03-27-2025, 11:17 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Thanks Rodb looking at your picture of the cable I was able to reconnect the original cable just slightly shorter and ab...osanders0311 — 09:02 PM
Philco 42-345 Restoration/Repair
Ah Ok I've taken the spring off and removed the broken piece, looks like I would lose about an inch using the current ca...osanders0311 — 08:21 PM
Philco 42-345 Restoration/Repair
The string is held tight with springs. I use black 20 pound test nylon fishing line (plentiful here in MN). Take picture...RodB — 07:15 PM
Philco 42-345 Restoration/Repair
Thank you very much for your help and sending the pictures, the cables must have been wrapped very tight around the spin...osanders0311 — 06:52 PM
Philco 42-345 Restoration/Repair
As you can see, mine has a chunk of hard rubber remnant on the shaft next to the chassis. I would say the shaft was, at ...RodB — 06:13 PM
VTVM meter moves when my hand is next to it & not on
It's  okay because my wife hoards yarn, so one more piece of radio rest equipment is ok tooBruce B — 05:56 PM
Philco 42-345 Restoration/Repair
I think my 42-340 is the same as your 345 without the buttons. Give me a few minutes and I'll pull the chassis and I'll ...RodB — 05:43 PM
VTVM meter moves when my hand is next to it & not on
Can't turn that deal down.RodB — 05:23 PM
VTVM meter moves when my hand is next to it & not on
Thanks Bob, I was kinda figuring on that, but I have never seen anything like this guy does.  It's inability to come ba...Bruce B — 04:59 PM
Philco 42-345 Restoration/Repair
I have attached a markup of the channel selector cable upper right in the picture under the chassis, this cable is broke...osanders0311 — 04:40 PM

[-]
Who's Online
There are currently 2271 online users. [Complete List]
» 2 Member(s) | 2269 Guest(s)
AvatarAvatar

>