1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Atwater Kent 708 Flexible Resistor Identification Needed
Tonym4704
Junior Member
**
Posts: 12
Threads: 6
Joined: Jun 2024
City: Shirley State, Province, Country: MA
#1

Yesterday, 05:14 PM
Hello Everyone,
I am in the process of rebuilding the sub-chassis in an Atwater Kent 708 radio serial number 4796904 and I am having a problem identifying the four flexible resistors. The schematic that I found online has a different arrangement and shows only three flexible resistors. If someone could please supply a diagram that is the match for my model and showing the resistor values I would appreciate it.
The diagram I have drawn up shows the four resistors in different colors. The red one checks at 200 ohms and the green is 432 ohms. The blue and purple resistors on the lower left side of the diagram are both open and the values for these are what I am searching for. Thank you.
Paul


Attached Files Image(s)
       
(This post was last modified: Yesterday, 05:16 PM by Tonym4704.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Atwater Kent 708 Flexible Resistor Identification Needed - by Tonym4704 - Yesterday, 05:14 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Atwater Kent 708 Flexible Resistor Identification Needed
Tony Could you possibly trace the flexes to where they go in your chassis? Should'nt be too hard.morzh — 09:23 PM
Atwater Kent 708 Flexible Resistor Identification Needed
None of the diagrams that are shown online are the same as what I have drawn. It is my setup with the two resistors conn...Tonym4704 — 08:47 PM
Atwater Kent 708 Flexible Resistor Identification Needed
morzh You are right. Scematic 808 is corresponded requered. On this case Purple - R11A 160 ohms Red - R11B 160 ohms Bu...Vlad95 — 08:07 PM
Atwater Kent 708 Flexible Resistor Identification Needed
Have you looked in here? And in here. 708, 808 and 808A are very similar.morzh — 07:43 PM
Atwater Kent 708 Flexible Resistor Identification Needed
Hello, That diagram in Rider's is a little different from the setup that I have. Note that the R11 resistor connects to...Tonym4704 — 07:37 PM
Atwater Kent 708 Flexible Resistor Identification Needed
According scematic in "Rider volume" #4 page 17 Green - R1 425 ohms (corresponded your measurement) Blue -...Vlad95 — 07:10 PM
Atwater Kent 708 Flexible Resistor Identification Needed
Hello Everyone, I am in the process of rebuilding the sub-chassis in an Atwater Kent 708 radio serial number 4796904 an...Tonym4704 — 05:14 PM
Zenith H725
Yes this set has a neon pilot lamp, type NE51.EdHolland — 08:04 AM
Philco model 40-100
Hi Marion, I don't know; I never researched it. I would think that function would be really annoying, but it would be...MrFixr55 — 07:59 AM
Philco model 40-100
MrFixr55 In regard to your RCA 14BT2 radio with the blinking neon lamp, I have an RCA BT-41 farm radio that has the sam...mhamby — 10:46 PM

[-]
Who's Online
There are currently 221 online users. [Complete List]
» 3 Member(s) | 218 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)