Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Caps List?
#2

Dark, Welcome to the Philco phorum!
I don't think there is any list that gives you a list to buy from a vendor the specific caps you need for that model. You need to do some research on your model at nostalgiaair.org.There you can search for your schematic and parts list and figure out what you need.Then you need to find a vendor or store that sells them. We buy from many different places. Radio daze,just radios,radio antiques,etc.


Messages In This Thread
Caps List? - by Dark High - 08-17-2011, 08:52 AM
Re: Caps List? - by Chicago Jimmy - 08-17-2011, 04:41 PM
Re: Caps List? - by Marsupial - 08-17-2011, 09:38 PM
Re: Caps List? - by Dark High - 08-18-2011, 10:27 AM
Re: Caps List? - by exray - 08-18-2011, 10:49 AM
Re: Caps List? - by dcastor - 08-18-2011, 12:00 PM
Re: Caps List? - by Dark High - 08-19-2011, 10:28 AM
Re: Caps List? - by Ron Ramirez - 08-19-2011, 12:34 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently 1409 online users. [Complete List]
» 1 Member(s) | 1408 Guest(s)
Avatar

>