Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Christmas in August
#26

Thanks to everyone for the well wishes, I really appreciate your kindness.

Paul - as I mentioned earlier in this thread, I bought myself the 37-690 as a graduation present for myself, having earned my associate degree in Information Technology, Summa Cum Laude, Phi Theta Kappa (3.974 GPA). Not bad for an old man.

Tom (TA) - That is a very nice thing to say, thank you!

Arran - Sorry, I don't have a video camera. (Although, I think Debbie might have one?) Anyway, this 37-690 is working and has been worked on in the recent past. However, at some point I am probably going to go through it again. I looked under the upper chassis and found that none of the bakelite blocks had been rebuilt; new yellow Mylar caps were connected across the bakelite blocks instead. This set deserves a proper electronic restoration, and as time allows, it shall receive one. I guess I had better start saving those old wax paper caps for when the time comes to do this, else I'll be in the same boat as Etech when he redid his 38-690. I usually don't bother restuffing wax paper caps. But on a really nice set such as this one, yes, I will take the extra effort to do this.

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Christmas in August - by Ron Ramirez - 08-07-2011, 08:27 PM
Re: Christmas in August - by w4rtc - 08-07-2011, 09:04 PM
Re: Christmas in August - by gvel - 08-07-2011, 09:26 PM
Re: Christmas in August - by Dan Walker - 08-07-2011, 10:46 PM
Re: Christmas in August - by codefox1 - 08-07-2011, 11:26 PM
Re: Christmas in August - by Glenn Roberts - 08-08-2011, 04:14 AM
Re: Christmas in August - by Ron Ramirez - 08-08-2011, 07:54 AM
Re: Christmas in August - by Michael Dennis - 08-08-2011, 08:56 AM
Re: Christmas in August - by etech - 08-08-2011, 09:07 AM
Re: Christmas in August - by Guest - 08-08-2011, 09:09 AM
Re: Christmas in August - by Ron Ramirez - 08-08-2011, 09:29 AM
Re: Christmas in August - by Guest - 08-08-2011, 09:47 AM
Re: Christmas in August - by Ron Ramirez - 08-08-2011, 09:59 AM
Re: Christmas in August - by Guest - 08-08-2011, 11:08 AM
Re: Christmas in August - by Jayce - 08-08-2011, 11:11 AM
Re: Christmas in August - by Ron Ramirez - 08-08-2011, 11:19 AM
Re: Christmas in August - by Uffda - 08-08-2011, 01:27 PM
Re: Christmas in August - by Jayce - 08-08-2011, 05:39 PM
Re: Christmas in August - by 37silverstreak - 08-08-2011, 08:31 PM
Re: Christmas in August - by Eliot Ness - 08-09-2011, 10:29 AM
Re: Christmas in August - by 7estatdef - 08-10-2011, 07:02 PM
Re: Christmas in August - by Chuck Schwark - 08-10-2011, 08:31 PM
Re: Christmas in August - by Paul Philco322 - 08-10-2011, 09:30 PM
Re: Christmas in August - by TA Forbes - 08-11-2011, 06:30 PM
Re: Christmas in August - by Arran - 08-12-2011, 08:37 PM
Re: Christmas in August - by Ron Ramirez - 08-20-2011, 07:41 AM
Re: Christmas in August - by etech - 08-22-2011, 08:48 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM
54C Complete Teardown/Rebuild
Richard, Had grabbed it already but thank you just the same.  I find myself wanting to find some way to block out the...glyphmon — 12:03 AM
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting.  IF alignment went great, almost all was already spot-on.  Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project.  O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today.  Soldered one in and had a successful first power-up.  No magic smoke escaped and it tunes in...glyphmon — 09:53 PM

[-]
Who's Online
There are currently 1545 online users. [Complete List]
» 1 Member(s) | 1544 Guest(s)
Avatar

>