1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 71 restoration
Arran
Phorum Expert
*****
Posts: 4,705
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#7

10-06-2011, 02:24 AM
Ron Ramirez Wrote:Good that you are making progress. I've been reading your posts but haven't had a chance to dig out my 71 schematics and make an intelligent comment.

That reminds me, I still have to look inside the chassis of my 118B and find the shunt resistor for the shadowmeter so I can tell GlennPR where it is located. It isn't shown in the under-chassis diagram. Nice of Philco to occasionally leave out a detail or three here and there, eh?

By the way, the new cone on the speaker looks great. Two thumbs up to Hank Brazeal. Icon_thumbup Icon_thumbup

That's strange, it's shown on the under chassis diagram I have for a Canadian Philco 3118. It's basically a porcelain tube with wire wrapped around it mounted in a threaded rod roughly legthwise in the center of the chasis, the reason I know about it is that mine is open. Now if only I could find a 9'' Philco speaker for my 3118, I think it's a K7 type.
Regards
Arran
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 71 restoration - by ipwizard - 09-29-2011, 12:48 AM
RE: Philco 71 restoration - by ipwizard - 03-02-2012, 06:09 PM
Re: Man this thing is a nightmare - by ipwizard - 09-29-2011, 01:36 AM
Re: Man this thing is a nightmare - by ipwizard - 09-29-2011, 10:14 PM
Re: Man this thing is a nightmare - by ipwizard - 10-06-2011, 12:29 AM
Re: Man this thing is a nightmare - by Arran - 10-06-2011, 02:24 AM
Re: Man this thing is a nightmare - by rghines1 - 10-06-2011, 10:20 AM
Re: Man this thing is a nightmare - by exray - 10-06-2011, 12:41 PM
Re: Man this thing is a nightmare - by ipwizard - 10-08-2011, 10:34 PM
Re: Man this thing is a nightmare - by Marsupial - 10-08-2011, 11:52 PM
Re: Man this thing is a nightmare - by exray - 10-09-2011, 05:56 AM
Re: Man this thing is a nightmare - by ipwizard - 10-10-2011, 01:40 PM
Re: Philco 71 restoration - by ipwizard - 10-31-2011, 05:10 PM
Re: Philco 71 restoration - by 7estatdef - 10-31-2011, 08:48 PM
Re: Philco 71 restoration - by 7estatdef - 10-31-2011, 09:00 PM
Re: Philco 71 restoration - by ipwizard - 11-01-2011, 01:03 AM
Re: Philco 71 restoration - by ipwizard - 11-01-2011, 01:06 AM
Re: Philco 71 restoration - by 7estatdef - 11-01-2011, 10:58 PM
Re: Philco 71 restoration - by ipwizard - 11-03-2011, 01:03 AM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 02:59 AM
Re: Philco 71 restoration - by codefox1 - 11-03-2011, 10:04 AM
Re: Philco 71 restoration - by ipwizard - 11-03-2011, 06:00 PM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 06:26 PM
Re: Philco 71 restoration - by ipwizard - 11-03-2011, 06:31 PM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 06:42 PM
Re: Philco 71 restoration - by ipwizard - 11-03-2011, 07:40 PM
Re: Philco 71 restoration - by 7estatdef - 11-03-2011, 08:39 PM
Re: Philco 71 restoration - by ipwizard - 11-03-2011, 09:38 PM
Re: Philco 71 restoration - by ipwizard - 11-04-2011, 12:29 AM
Re: Philco 71 restoration - by ipwizard - 11-04-2011, 02:33 PM
Re: Philco 71 restoration - by ipwizard - 11-30-2011, 11:56 PM
Re: Philco 71 restoration - by TA Forbes - 12-01-2011, 12:37 AM
Re: Philco 71 restoration - by TA Forbes - 12-02-2011, 09:54 PM
Re: Philco 71 restoration - by codefox1 - 12-03-2011, 11:48 AM
Re: Philco 71 restoration - by ipwizard - 12-04-2011, 03:03 PM
Re: Philco 71 restoration - by ipwizard - 12-23-2011, 04:36 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM

[-]
Who's Online
There are currently 6268 online users. [Complete List]
» 1 Member(s) | 6267 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration