Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

transporting my philco 37-630X
#2

Make sure that the speaker is secure in the radio. Tighten it down if not. Same for the chassis, make sure it is secure in the cabinet and tighten if it is not. Lay a blanket in the back of your suv and place the radio back side down on the blanket, with the top of the radio facing the front of the suv. You can pull on the blanket to position the radio in your suv and conversely pull on the blanket to slide the radio out.

While the radio is on its back would be a good time to put felt cushions on the bottom of the cabinet. This makes it easier to move your radio on hardwood, vinyl, or tile floors. If you are going to move the radio on a rug, use a towel or blanket under it and pull the towel or blanket to slide it.


Messages In This Thread
transporting my philco 37-630X - by kbm37-630 - 10-11-2011, 08:06 PM
Re: transporting my philco 37-630X - by TA Forbes - 10-11-2011, 09:30 PM
Re: transporting my philco 37-630X - by TA Forbes - 10-11-2011, 09:54 PM
Re: transporting my philco 37-630X - by kbm37-630 - 10-12-2011, 05:49 AM
Re: transporting my philco 37-630X - by Uffda - 10-15-2011, 12:24 PM
Re: transporting my philco 37-630X - by Steve D - 10-15-2011, 04:06 PM
Re: transporting my philco 37-630X - by Uffda - 10-15-2011, 04:47 PM
Re: transporting my philco 37-630X - by kbm37-630 - 10-17-2011, 01:49 PM
Re: transporting my philco 37-630X - by TA Forbes - 10-18-2011, 12:14 AM
Re: transporting my philco 37-630X - by Uffda - 11-13-2011, 11:40 AM
Re: transporting my philco 37-630X - by kbm37-630 - 11-13-2011, 01:32 PM
Re: transporting my philco 37-630X - by Uffda - 11-13-2011, 02:10 PM
Re: transporting my philco 37-630X - by kbm37-630 - 11-13-2011, 03:26 PM
Re: transporting my philco 37-630X - by Uffda - 11-13-2011, 04:21 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural....morzh — 08:40 PM
Hickok AC51 tube tester
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM
Shadow Meter Bulb
Ross I am not sure what current limiting effect the incandescent provides. They are two different parts of the sch...morzh — 08:31 PM
12' Philco
Bob Thanks for that photo. I have been looking for it, and I cannot find anythinmg on the web. I forgot it was here...morzh — 08:29 PM
Shadow Meter Bulb
I think after all has been said, I will use the same bulb that is specified for the dial pilot light which is a #55. I ...georgetownjohn — 07:31 PM
12' Philco
There was also this Philco! klondike98 — 07:25 PM
HiFi (Chifi) tube amp build - but my own design.
I expected a challenge and this is just part of it. But, it's also supposed to be fun, entertaining, informative and enj...TV MAN — 07:12 PM
Shadow Meter Bulb
Butting in here with a question. Since the shadow meter is connected directly to the 1st and 2nd I.F.'s wouldn't the met...RossH — 06:43 PM
HiFi (Chifi) tube amp build - but my own design.
Mike, Tim; you are about to enter the twilight zone. Doo doo doo doo, doo doo doo doo This is something alright. I'm go...RodB — 06:26 PM

[-]
Who's Online
There are currently no members online.

>