transporting my philco 37-630X

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

transporting my philco 37-630X

Uffda
Member

Posts: 244
Threads: 24
Joined: Feb 2006

10-15-2011, 04:47 PM

A piece of styrofoam cut out and taped around the knobs will help keep the knob shafts from being jammed and damaged. Something taped over the speaker grille might be worthwhile too if thought out on where the stresses will be. Interior bracing limited only by your patience. Of course, usually I just say "Ah, too much work, I'll be careful." Which is USUALLY good enough. Your mileage may vary.

Phil aka Philbert Q. Desenex - Twin Cities, MN

Find

« Next Oldest | Next Newest »

Messages In This Thread

transporting my philco 37-630X - by kbm37-630 - 10-11-2011, 08:06 PM

Re: transporting my philco 37-630X - by TA Forbes - 10-11-2011, 09:30 PM

Re: transporting my philco 37-630X - by 37silverstreak - 10-11-2011, 09:33 PM

Re: transporting my philco 37-630X - by TA Forbes - 10-11-2011, 09:54 PM

Re: transporting my philco 37-630X - by kbm37-630 - 10-12-2011, 05:49 AM

Re: transporting my philco 37-630X - by Uffda - 10-15-2011, 12:24 PM

Re: transporting my philco 37-630X - by Ron Ramirez - 10-15-2011, 02:04 PM

Re: transporting my philco 37-630X - by Steve D - 10-15-2011, 04:06 PM

Re: transporting my philco 37-630X - by Uffda - 10-15-2011, 04:47 PM

Re: transporting my philco 37-630X - by Ron Ramirez - 10-15-2011, 05:26 PM

Re: transporting my philco 37-630X - by Texasrocker - 10-15-2011, 08:08 PM

Re: transporting my philco 37-630X - by kbm37-630 - 10-17-2011, 01:49 PM

Re: transporting my philco 37-630X - by TA Forbes - 10-18-2011, 12:14 AM

Re: transporting my philco 37-630X - by Ron Ramirez - 11-13-2011, 07:29 AM

Re: transporting my philco 37-630X - by Uffda - 11-13-2011, 11:40 AM

Re: transporting my philco 37-630X - by kbm37-630 - 11-13-2011, 01:32 PM

Re: transporting my philco 37-630X - by Uffda - 11-13-2011, 02:10 PM

Re: transporting my philco 37-630X - by kbm37-630 - 11-13-2011, 03:26 PM

Re: transporting my philco 37-630X - by Uffda - 11-13-2011, 04:21 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit. That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural....morzh — 08:40 PM
Hickok AC51 tube tester
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM
Shadow Meter Bulb
Ross I am not sure what current limiting effect the incandescent provides. They are two different parts of the sch...morzh — 08:31 PM
12' Philco
Bob Thanks for that photo. I have been looking for it, and I cannot find anythinmg on the web. I forgot it was here...morzh — 08:29 PM
Shadow Meter Bulb
I think after all has been said, I will use the same bulb that is specified for the dial pilot light which is a #55. I ...georgetownjohn — 07:31 PM
12' Philco
There was also this Philco! klondike98 — 07:25 PM
HiFi (Chifi) tube amp build - but my own design.
I expected a challenge and this is just part of it. But, it's also supposed to be fun, entertaining, informative and enj...TV MAN — 07:12 PM
Shadow Meter Bulb
Butting in here with a question. Since the shadow meter is connected directly to the 1st and 2nd I.F.'s wouldn't the met...RossH — 06:43 PM
HiFi (Chifi) tube amp build - but my own design.
Mike, Tim; you are about to enter the twilight zone. Doo doo doo doo, doo doo doo doo This is something alright. I'm go...RodB — 06:26 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me