Philco model 511

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco model 511

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

#33

10-31-2011, 06:57 PM

I can't give you a color code for the original wires because one does not appear to exist. It is not mentioned in Service Bulletin 5 (which covers the 511 Series), nor in the long form service manual for these sets, the Philco Radio Manual of Useful Information.

It appears that a majority of the 511 Series sets were made with the six-terminal resistor, and a separate 70K resistor mounted on the end of the chassis. With this setup, think of the terminals of the multi-section resistor as having terminals 1, 2, 3, 6, 7 and 8 with no connection between terminals 3 and 6. Terminals 4 and 5 make up the separate 70K resistor.

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco model 511 - by radionut1929 - 08-14-2011, 02:42 AM

Re: Philco model 511 - by 7estatdef - 08-15-2011, 07:33 AM

Re: Philco model 511 - by radionut1929 - 08-15-2011, 10:16 PM

Re: Philco model 511 - by 7estatdef - 08-15-2011, 10:24 PM

Re: Philco model 511 - by codefox1 - 08-15-2011, 10:40 PM

Re: Philco model 511 - by radionut1929 - 08-16-2011, 12:18 AM

Re: Philco model 511 - by radionut1929 - 08-16-2011, 12:22 AM

Re: Philco model 511 - by Ron Ramirez - 08-16-2011, 07:58 AM

Re: Philco model 511 - by 7estatdef - 08-16-2011, 06:39 PM

Re: Philco model 511 - by gvel - 08-16-2011, 08:34 PM

Re: Philco model 511 - by radionut1929 - 08-18-2011, 06:11 AM

Re: Philco model 511 - by Ron Ramirez - 08-18-2011, 07:47 AM

Re: Philco model 511 - by radionut1929 - 08-21-2011, 05:40 PM

Re: Philco model 511 - by codefox1 - 08-21-2011, 05:52 PM

Re: Philco model 511 - by Ron Ramirez - 08-21-2011, 07:45 PM

Re: Philco model 511 - by radionut1929 - 08-22-2011, 03:12 AM

Re: Philco model 511 - by 7estatdef - 08-22-2011, 03:15 PM

Re: Philco model 511 - by Ron Ramirez - 08-22-2011, 03:30 PM

Re: Philco model 511 - by 7estatdef - 08-22-2011, 03:56 PM

Re: Philco model 511 - by Ron Ramirez - 08-22-2011, 03:58 PM

Re: Philco model 511 - by Eliot Ness - 08-22-2011, 05:37 PM

Re: Philco model 511 - by radionut1929 - 08-23-2011, 03:29 AM

Re: Philco model 511 - by Ron Ramirez - 08-24-2011, 03:16 PM

Re: Philco model 511 - by radionut1929 - 08-30-2011, 11:27 PM

Re: Philco model 511 - by Arran - 08-30-2011, 11:46 PM

Re: Philco model 511 - by Ron Ramirez - 08-31-2011, 11:05 AM

Re: Philco model 511 - by radionut1929 - 09-12-2011, 02:06 AM

Re: Philco model 511 - by Ron Ramirez - 09-12-2011, 10:37 AM

Re: Philco model 511 - by TA Forbes - 09-12-2011, 09:21 PM

Re: Philco model 511 - by radionut1929 - 09-12-2011, 11:33 PM

Re: Philco model 511 - by radionut1929 - 10-28-2011, 12:21 AM

Re: Philco model 511 - by jerryhawthorne - 10-30-2011, 01:26 PM

Re: Philco model 511 - by Ron Ramirez - 10-31-2011, 06:57 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online

There are currently 6373 online users. [Complete List]
» 4 Member(s) | 6369 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me