1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Value of caps in block?????
Dan Walker
Senior Member
****
Posts: 383
Threads: 105
Joined: Jul 2011
City: Calgary, AB, CA
#3

11-16-2011, 06:53 PM
Ron I must say that I am sorry but I made a mistake in the numbers of the block... The proper number is 4989Z which[using the info you gave me ] transfers to a number of 4989 odg...If I have this right it means that I can put two caps of .10 in the block and hook them up to the same pins as the old ones.. According to what I see it is #1 to #5 and #2 to #3...[.Pin #1 and #2 are connected and go to ground] WOULD THIS BE CORRECT?
Once again I am sorry for the inconvenience this may have caused you,I will be more carefull with my numbers next time. Thank you Dan
   Living in Calgary Alberta
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Value of caps in block????? - by Dan Walker - 11-16-2011, 04:19 PM
Re: Value of caps in block????? - by Ron Ramirez - 11-16-2011, 06:09 PM
Re: Value of caps in block????? - by Dan Walker - 11-16-2011, 06:53 PM
Re: Value of caps in block????? - by Ron Ramirez - 11-16-2011, 08:23 PM
Re: Value of caps in block????? - by Texasrocker - 11-16-2011, 09:39 PM
Re: Value of caps in block????? - by LASJayhawk - 12-08-2011, 10:15 PM
Re: Value of caps in block????? - by Ron Ramirez - 12-09-2011, 06:32 AM
Re: Value of caps in block????? - by DeckApe - 12-11-2011, 12:54 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
[split] New member...
Well, with the replacement tuning assembly, I have finally put the unit back together and aligned the dial.  The first s...HowardWoodard — 01:01 AM
Philco Model 16 wiring question
Well, finding a short is easy. Like I said, disconnect the transformer's secondary windings and see if it persists. If...morzh — 09:48 PM
Restoring Philco 96
Nice one!Stan the Man — 09:37 PM
Restoring Philco 96
I have eventually replaced the speaker and shot the video, which only shows the upper part of the dial as the hum is ver...morzh — 09:24 PM
Rogers Majestic R-646
Kinda weird to see both open Nothing weird if you remember that this radio is about 100 years old  :)Vlad95 — 07:49 PM
Philco 42-345 Restoration/Repair
I believe I'm making progress, resistors have been rechecked and corrected, removed that ugly blue capacitor and more wi...osanders0311 — 07:38 PM
Philco Model 16 wiring question
Thanks Morzh Yes I recapped everything and replaced almost all the resistors as well. I redid #99 with .015 safety ca...bobclausen — 07:11 PM
Philco Model 16 wiring question
Well...pull out every single load of the transformer. For every winding. Unsolder if needed. Then re-do your dim bulb....morzh — 07:02 PM
Rogers Majestic R-646
Kinda weird to see both open, but once you get it up and running, really pay attention to your sound. Listen for loud cr...TV MAN — 06:59 PM
Rogers Majestic R-646
Vlad; I was just reminded of something else, I'm not sure why but many Rogers built sets do seem to have open primari...Arran — 04:40 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration