Re-stuffing the Power Filter Box Can assembly in Philco20

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Re-stuffing the Power Filter Box Can assembly in Philco20

Radioroslyn
Phorum Expert

Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

11-23-2011, 05:12 PM

Put it upright in the oven. Bake it at 275 for 30-45min. Use a cork screw or a large I hook to screw into the paper caps and pull them out of the can. The first one is the hardest.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Re-stuffing the Power Filter Box Can assembly in Philco20 - by morzh - 11-22-2011, 05:56 PM

Re: Re-stuffing the Power Filter Box Can assembly in Philco2 - by 7estatdef - 11-23-2011, 05:12 PM

Re: Re-stuffing the Power Filter Box Can assembly in Philco2 - by Texasrocker - 11-23-2011, 11:24 PM

Re: Re-stuffing the Power Filter Box Can assembly in Philco2 - by Arran - 11-24-2011, 01:01 AM

Re: Re-stuffing the Power Filter Box Can assembly in Philco2 - by morzh - 11-24-2011, 01:13 PM

Re: Re-stuffing the Power Filter Box Can assembly in Philco2 - by 7estatdef - 11-25-2011, 11:13 AM

Re: Re-stuffing the Power Filter Box Can assembly in Philco2 - by Texasrocker - 11-26-2011, 11:46 PM

Re: Re-stuffing the Power Filter Box Can assembly in Philco2 - by Texasrocker - 11-27-2011, 02:44 AM

Re: Re-stuffing the Power Filter Box Can assembly in Philco2 - by morzh - 11-28-2011, 11:45 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online

There are currently 6322 online users. [Complete List]
» 4 Member(s) | 6318 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me