Philco 60 Alive Again!

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 60 Alive Again!

Caperodder
Junior Member

Posts: 47
Threads: 5
Joined: Oct 2011
City: West Barnstable, Massachu

#17

12-04-2011, 11:06 AM

Thanks Terry.

The smallest my RS has is 30 gauge. Resistance is something like 100 ohm/ft vs 650 ohm/ft for 38. that might be stretching it a little, not sure. Everything I have found so far online, is like 1400 ft spools. Hate to buy that when I need less than 2' of wire. I'm also looking through some junk equipment for something like .004/.005/.006 diameter mag wire.

I'll continue looking.

-Brett

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 60 Alive Again! - by Caperodder - 12-02-2011, 04:04 PM

Re: Philco 60 Alive Again! - by Chicago Jimmy - 12-02-2011, 06:21 PM

Re: Philco 60 Alive Again! - by 7estatdef - 12-02-2011, 07:14 PM

Re: Philco 60 Alive Again! - by Phlogiston - 12-02-2011, 07:56 PM

Re: Philco 60 Alive Again! - by Ron Ramirez - 12-02-2011, 08:40 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-02-2011, 09:30 PM

Re: Philco 60 Alive Again! - by 7estatdef - 12-02-2011, 09:58 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-03-2011, 09:04 AM

Re: Philco 60 Alive Again! - by gvel - 12-03-2011, 09:09 AM

Re: Philco 60 Alive Again! - by Caperodder - 12-03-2011, 09:50 AM

Re: Philco 60 Alive Again! - by 7estatdef - 12-03-2011, 05:19 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-03-2011, 06:05 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-03-2011, 06:45 PM

Re: Philco 60 Alive Again! - by Ron Ramirez - 12-03-2011, 07:27 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-03-2011, 07:34 PM

Re: Philco 60 Alive Again! - by 7estatdef - 12-04-2011, 10:06 AM

Re: Philco 60 Alive Again! - by Caperodder - 12-04-2011, 11:06 AM

Re: Philco 60 Alive Again! - by morzh - 12-04-2011, 12:46 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-04-2011, 01:16 PM

Re: Philco 60 Alive Again! - by 7estatdef - 12-04-2011, 03:05 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-04-2011, 06:37 PM

Re: Philco 60 Alive Again! - by 7estatdef - 12-04-2011, 07:04 PM

Re: Philco 60 Alive Again! - by 7estatdef - 12-04-2011, 11:49 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-05-2011, 11:20 AM

Re: Philco 60 Alive Again! - by 7estatdef - 12-05-2011, 12:11 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-05-2011, 03:46 PM

Re: Philco 60 Alive Again! - by 7estatdef - 12-05-2011, 04:12 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-05-2011, 05:53 PM

Re: Philco 60 Alive Again! - by 7estatdef - 12-05-2011, 06:25 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-05-2011, 07:20 PM

Re: Philco 60 Still dead - by 7estatdef - 12-05-2011, 10:09 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-05-2011, 11:01 PM

Re: Philco 60 Alive Again! - by Caperodder - 12-05-2011, 11:19 PM

Re: Philco 60 Alive Again! - by 7estatdef - 12-07-2011, 09:18 AM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online

There are currently 5535 online users. [Complete List]
» 4 Member(s) | 5531 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me