Philco 41-280

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 41-280

OldJack1969
Junior Member

Posts: 21
Threads: 3
Joined: Dec 2011
City: North Las Vegas, NV

#14

01-08-2012, 12:43 AM

Sorry it took so long to get back to you... yes, it is working the way it should. The schematic shows an 8uf ecap from ground to that 18 ohm resistor, are you sure I should replace it with a 10 or 20uf cap?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 41-280 - by OldJack1969 - 01-03-2012, 07:08 PM

Re: Philco 41-280 - by 7estatdef - 01-03-2012, 08:52 PM

Re: Philco 41-280 - by OldJack1969 - 01-04-2012, 06:55 PM

Re: Philco 41-280 - by 7estatdef - 01-04-2012, 11:49 PM

Re: Philco 41-280 - by OldJack1969 - 01-05-2012, 12:00 AM

Re: Philco 41-280 - by OldJack1969 - 01-05-2012, 01:09 AM

Re: Philco 41-280 - by 7estatdef - 01-05-2012, 07:28 PM

Re: Philco 41-280 - by OldJack1969 - 01-05-2012, 08:25 PM

Re: Philco 41-280 - by 7estatdef - 01-05-2012, 11:28 PM

Re: Philco 41-280 - by OldJack1969 - 01-06-2012, 12:05 AM

Re: Philco 41-280 - by 7estatdef - 01-06-2012, 08:47 AM

Re: Philco 41-280 - by OldJack1969 - 01-06-2012, 01:35 PM

Re: Philco 41-280 - by 7estatdef - 01-06-2012, 05:42 PM

Re: Philco 41-280 - by OldJack1969 - 01-08-2012, 12:43 AM

Re: Philco 41-280 - by Phlogiston - 01-08-2012, 12:56 AM

Re: Philco 41-280 - by OldJack1969 - 01-08-2012, 01:10 AM

Re: Philco 41-280 - by 7estatdef - 01-08-2012, 03:30 PM

Re: Philco 41-280 - by OldJack1969 - 01-08-2012, 03:45 PM

Re: Philco 41-280 - by gary rabbitt - 01-23-2012, 08:38 PM

Re: Philco 41-280 - by OldJack1969 - 01-23-2012, 09:29 PM

Re: Philco 41-280 - by gary rabbitt - 01-24-2012, 04:58 PM

Re: Philco 41-280 - by OldJack1969 - 01-24-2012, 05:10 PM

Re: Philco 41-280 - by 7estatdef - 01-24-2012, 06:17 PM

Re: Philco 41-280 - by OldJack1969 - 01-24-2012, 06:50 PM

Re: Philco 41-280 - by 7estatdef - 01-24-2012, 06:56 PM

Re: Philco 41-280 - by OldJack1969 - 01-24-2012, 07:15 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

Who's Online

There are currently 4903 online users. [Complete List]
» 2 Member(s) | 4901 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me