RCA K130 RC501a chassis

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

RCA K130 RC501a chassis

murf
Senior Member

Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.

#17

01-12-2012, 02:10 PM

Sean Wrote:
murf Wrote:Being new to this,and not being in the electronics field,I am still trying to get an understanding of how these work.
Apparently,the capacitor values are dc voltage?The same for the electrolitics?
Sorry to bug you with such simple questions.
Just want to make sure I know what to buy when replacing that cap.
Have a great evening.
murf

Probably 99% of the time the voltage rating on a capacitor is DC voltage. You do find motor start or run capacitors that are rated for AC voltage but I think they usually also have a DC voltage rating.

Thank you sir,
I wonder if the 2, 25's are why it does not run.Should be 60.
Have a great day Sean and thanks
murf

Find

« Next Oldest | Next Newest »

Messages In This Thread

RCA K130 RC501a chassis - by murf - 01-08-2012, 02:31 PM

RE: RCA K130 RC501a chassis - by murf - 09-03-2012, 05:12 PM

Re: RCA K130 RC501a chassis - by Sean - 01-08-2012, 03:08 PM

Re: RCA K130 RC501a chassis - by murf - 01-08-2012, 03:17 PM

Re: RCA K130 RC501a chassis - by murf - 01-09-2012, 04:36 PM

Re: RCA K130 RC501a chassis - by Sean - 01-09-2012, 06:00 PM

Re: RCA K130 RC501a chassis - by 7estatdef - 01-09-2012, 09:58 PM

Re: RCA K130 RC501a chassis - by murf - 01-09-2012, 11:04 PM

Re: RCA K130 RC501a chassis - by 7estatdef - 01-09-2012, 11:37 PM

Re: RCA K130 RC501a chassis - by murf - 01-10-2012, 12:09 AM

Re: RCA K130 RC501a chassis - by murf - 01-10-2012, 09:03 PM

Re: RCA K130 RC501a chassis - by Sean - 01-11-2012, 10:47 AM

Re: RCA K130 RC501a chassis - by murf - 01-11-2012, 11:11 AM

Re: RCA K130 RC501a chassis - by murf - 01-11-2012, 03:09 PM

Re: RCA K130 RC501a chassis - by Sean - 01-11-2012, 05:31 PM

Re: RCA K130 RC501a chassis - by murf - 01-11-2012, 07:37 PM

Re: RCA K130 RC501a chassis - by Sean - 01-12-2012, 01:32 PM

Re: RCA K130 RC501a chassis - by murf - 01-12-2012, 02:10 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me