Alignment instructions needed

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Alignment instructions needed

ipwizard
Senior Member

Posts: 335
Threads: 50
Joined: Apr 2011
City: Apple Creek State, Province, Country: Ohio

#24

01-13-2012, 01:41 AM

The new 36 tube did the trick no for popping and motorboating on power on.

Thanks everyone that helped out.. Now on to the cabinet..

-Keith

Find

« Next Oldest | Next Newest »

Messages In This Thread

Alignment instructions needed - by ipwizard - 01-01-2012, 05:18 PM

Re: Alignment instructions needed - by Carl Travis - 01-01-2012, 05:34 PM

Re: Alignment instructions needed - by 7estatdef - 01-02-2012, 01:04 PM

Re: Alignment instructions needed - by ipwizard - 01-04-2012, 12:45 AM

Re: Alignment instructions needed - by ipwizard - 01-04-2012, 01:14 AM

Re: Alignment instructions needed - by 7estatdef - 01-04-2012, 07:31 AM

Re: Alignment instructions needed - by ipwizard - 01-04-2012, 01:46 PM

Re: Alignment instructions needed - by ipwizard - 01-04-2012, 05:55 PM

Re: Alignment instructions needed - by 7estatdef - 01-04-2012, 07:16 PM

Re: Alignment instructions needed - by ipwizard - 01-04-2012, 08:50 PM

Re: Alignment instructions needed - by 7estatdef - 01-04-2012, 11:12 PM

Re: Alignment instructions needed - by ipwizard - 01-04-2012, 11:46 PM

Re: Alignment instructions needed - by 7estatdef - 01-05-2012, 12:16 AM

Re: Alignment instructions needed - by ipwizard - 01-05-2012, 01:42 AM

Re: Alignment instructions needed - by Ron Ramirez - 01-05-2012, 07:02 AM

Re: Alignment instructions needed - by ipwizard - 01-05-2012, 02:00 PM

Re: Alignment instructions needed - by 7estatdef - 01-05-2012, 07:14 PM

Re: Alignment instructions needed - by ipwizard - 01-06-2012, 12:57 AM

Re: Alignment instructions needed - by John R - 01-06-2012, 01:29 PM

Re: Alignment instructions needed - by ipwizard - 01-09-2012, 12:31 AM

Re: Alignment instructions needed - by 7estatdef - 01-09-2012, 09:23 AM

Re: Alignment instructions needed - by ipwizard - 01-09-2012, 01:56 PM

Re: Alignment instructions needed - by ipwizard - 01-11-2012, 12:33 AM

Re: Alignment instructions needed - by ipwizard - 01-13-2012, 01:41 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

Who's Online

There are currently 6783 online users. [Complete List]
» 1 Member(s) | 6782 Guest(s)