1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Volume Control Cleaning Tool
dnitram
Junior Member
**
Posts: 22
Threads: 8
Joined: Dec 2010
#1

01-20-2012, 09:41 AM
Some while ago I ran across a web site where an apparently older gentleman sold some pretty nifty aids and tools. I do remember he had a tool that apparently screwed onto the volume control shaft, allowing you to force cleaner into the sealed volume control to clean it. I remember trying to order it, sent a money order only to get it back, where he stated he needed to fabricate some more and was out at the time.

Anyone know who this fellow may be and how to get in touch with him?

One other quick one... Anyone seen or used the chassis tool that you place on your bench top allowing you to more easily work on some of those hard to get to chassis?

Thanks for your replies!
David
Find
« Next Oldest | Next Newest »


Messages In This Thread
Volume Control Cleaning Tool - by dnitram - 01-20-2012, 09:41 AM
Re: Volume Control Cleaning Tool - by Sean - 01-20-2012, 09:50 AM
Re: Volume Control Cleaning Tool - by dnitram - 01-21-2012, 12:28 PM
Re: Volume Control Cleaning Tool - by Eliot Ness - 01-23-2012, 09:24 AM
Re: Volume Control Cleaning Tool - by Carl Travis - 01-23-2012, 10:26 AM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 6645 online users. [Complete List]
» 1 Member(s) | 6644 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration